Pole updates

- Fixed rfid bug in ocpp.

- Fixed rfid card issue in stop transactions.

- Fixed OCPP error where transaction wasn't started when states passed from C to B to C.

- CB Master: Improved robustness of rfid charge track so that if one connector is fully charged and a different car wants to charge in the other connector it can now charge.

- CB Master: Fixed bug that wouldn't allow two connectors to charge with payment + RFID.

- CB Master/CB N: Rfid cards can start a charge in payment mode if rfid is enabled.

- CB Master: We check if measurer is flipped by connector instead of globally.

- CB Master: We check if measurer is flipped while configuring meter values so that they are sent correctly.

- CB N: Fixed cloud iot problem.

- CB Master: Configuration file is restored correctly in the case it's lost. This provoked the page not found error.

- CB Master: Fixed bug where a connector couldn't start a charge when there's a car on the other connector with state B.

- CB Master: Implemented callable meter values.

- CB Master: Meter power bug fix.

- CB N: General payment improvements.

- CB N: We now report property wire_connected so that in the payment method the parking can be charged.

- CB N: In payment method, when you move from status c to b, it does not allow you to reload again until you start a new transaction.

- CB N: Car state management D and E.

- CB N: Improved restart logic when any OCPP configuration is changed.

- CB Master: Fixed payment bug that sent the upload permission to the wrong connector.

- CB Master: Fixed bug that when two cars were connected and the B connector was in B status, when the card was swiped, the B was set to charge when the A should be set.

- CB Master: General meter improvements.

- CB Master: Total energy bug arrangement from version using imported and exported energy.

- Pole: Filter to reduce number of logs.

- CB Master: Improved OCPP smart charging balancing logic.

- CB Master: Meter restructuring.

- OCPP: General improvements in Smart Charging and Tx Profile implemented.

- OCPP: Changes due to restructuring of the meter.

- OCPP: Restructuring of smart charging. Obtain composite timetable with several profiles.

- CB N: Added diagnostic method.

- CB Master: Increased RFID SPI communication speed and lowered RFID gain if noise is detected.

- CB Master: Integrated SACI meter and changes so that the serial configuration per connector is not linked.

- CB Master: Code refactoring

- CB Master: Convert to positive the negative values read by Phoenix Contact measurer.

- CB Master: We delete BrowserMetrics from chromium that it sometimes fills up and eats up all the memory.

- CB Master: Refactored serial and made some changes that improve flexibility. We can now have one connector with one type of measurer and the other connector with a different type of measurer.

- CB Master: Adjusted the precision of Phoenix Contact monophasic measurers.

- CB N: Fixed bug provoked by changing local load balancing from v2c service.

- OCPP: Change availability of Persistant Data handler is now async so that we can call it without blocking the execution of the ServerController.

- OCPP: Starting point for get composite schedule done.

- OCPP: Relative profiles are handled but only for Smart Charge profiles where connector id is bigger than 0.

- OCPP: Fixed clear charging profiles.

- OCPP: Smart Charging Tx Profiles are now accepted.

- OCPP: In websocket connection, added "compression=None" since without it it doesn't work on latest Steve version.

- OCPP: Added next time check mechanism for Smart Charging so we check the next time any limit changes instead of every 30 seconds.

- OCPP: General Smart Charge improvements.

- OCPP: We handle decimal numbers on the Smart Charge profile's limit.

- OCPP, CB N and CB Master: Fixed bug when locked was modified and ocpp was activated but chargepoint isn't connected to any central system.

- CB Master: Fixed bug when OCPP charge is started where if connector 1 was charging, connector 0 couldn't start a charge.

- CB Master: Function to receive Smart Charge current and OCPP balancing.

- CB Master: Prevent crash in the case that .versions folder doesn't exist.

- CB Master: Register cards are now added to card cache.

- CB N: Changes due to Smart Charging

- OCPP: Smart Charging starting point fininshed.

- OCPP: Smart Charging configuration keys are handled.

- OCPP: Smart Charging profiles can be added and will be validated and can also be deleted.

- CB Master: Improvements in update process.

- CB Master: Changes so that screen indicates when a non registered RFID card is passed.

- CB N: Improvements in update process.

- OCPP: GetConfigurationKeys now returns unknown keys and we handle SupportedFileTransferProtocols key.

- Pole: Screen now shows when user passes a non registered RFID card.

- Pole: Romanian identifier moved to position 6 to maintain order language with Trydan.

- CB Master: We don't send wifi_info in report anymore and we have removed functions related to wifi_info.

- CB Master: RFID reader improvements. The charger reads continuously instead of intermittently, reduced read errors and antenna gain is now dynamic.

- CB Master: We store RFID cards in cache.

- CB N: RFID reader improvements. Case where two connectors are plugged in and a card is passed.

- CB N: We don't send wifi_info in report anymore.

- CB N: New communication method so that CB master can obtain RFID cards.

- CB Master: Improvement in connect/disconnect logic. Disconnection is less rigid and we increased network check from 5 seconds to 15 seconds.

- CB Master: CWe fix error provoked by blocking/unblocking when charger has OCPP activated and isn't connected to central system.

- CB Master: Increased RFID reader antenna gain.

- CB Master: Changes in access point page to configure static IP.

- CB N: When charger reconnects, it will only send report if a property has changed.

- CB N: Properties are now only reported when they have changed from previous value.

- CB N: We fix error provoked by blocking/unblocking when charger has OCPP activated and isn't connected to central system.

- CB N: Static IP configuration through access point.

- OCPP: We fix error provoked by blocking/unblocking when charger has OCPP activated and isn't connected to central system.

- CB Master: Fixed energy by hour bug.

- CB Master: Safeguard so that it doesn't fail when there's a missing network card and we try to obtain data usage.

- CB Master: Removed range validation from measurer for Carlo Gavazzi and Phoenix Contact measurers.

- OCPP: Removed range validation from measurer.

- Pole: Added Romanian language.

- CB N: We only change repository hash if it has changed.

- CB N: We show in log if i2c reconnects.

- CB Master: Adjustment in measurer so that it can handle int32 represented as uint.

- CB Master: Changes to reduce calls to has_internet_connection to consume less data.

- CB Master: Chargebox Cache now stores state of connectivity with V2C service to show it on the screen.

- CB N: Log improvements to not show get_has_internet_connection y and reduce error messages generated when i2c is not working.

- CB N: Changes to reduce calls to has_internet_connection to consume less data.

- CB N: Chargebox Cache now stores state of connectivity with V2C service.

- CB N: Seconds of timeout now return 0 instead of None if not set.

- OCPP: We log exception names since sometimes exception errors return empty string.

- OCPP: We capture error if there's an error when sending heartbeat.

- OCPP: We change client controller so that it's the same as CB N and CB Master.

- Pole: The screen now shows a cloud icon to indicate connectivity to our cloud.

- CB Master: Fixed error where RFID stops charge while the other connector is enabled.

- CB Master: Fixed error where RFID card is passed and both connectors have a car plugged in.

- CB Master: Network usage will be shown in log when a reboot is performed.

- CB Master: Master now sends the balanced intensity when it changes.

- CB N: Changed order of what happens when configuration is changed. We first update the value, then we report the changes to Azure and finally we set the cache.

- CB N: Fixed bug where changing local load balancing set both connector intensities to 16.

- CB N: CB Master now sends balanced intensity instead of CB N probing for change.

- CB Master: Network usage is now monitored.

- CB Master: Change in log system to not show repeated logs.

- CB Master: Shared properties are now set in the other connector if they are different on startup.

- CB Master: Completely decoupled OCPP from CB N and get_ocpp_config function fixed.

- CB Master: Network state is now sent when changed instead of being probed every 30 seconds.

- CB N: General improvements of communication between modules and cache.

- CB N: Improved stability related with missing configuration.

- CB N: Change in log system to not show repeated logs.

- CB N: Fixed problem where Chargebox loop would destroy RFID state.

- CB N: Fixed OCPP ConnectionTimeout.

- CB N: Completely decoupled OCPP from CB N

- CB N: Network state is now sent when changed instead of being probed every 30 seconds.

- CB N: We only change repository hash if it's different than the current one.

- CB N: Updating checks if charger is updated or not and only changes version after it has been updated.

- CB N: General improvements of communication between modules.

- OCPP: Improved Client Controller traceability.

- CB Master: Created singletons are now thread safe.

- CB Master: Created Cache to decrease the number of requests and communication between modules.

- CB Master: Fixed network reset problem.

- CB Master: Changes so that Pole can receive all the information it needs in one call.

- CB Master: Changes dues to how the measures are now sent.

- CB Master: General access point improvements.

- CB Master: Improvements due to changes in module communication.

- CB N: Created singletons are now thread safe.

- CB N: Server Controller is now executed sooner due to being fundamental in correct functioning.

- CB N: Changes to take into account CB Master's cache

- CB N: Changed way we obtain measures to perform less requests with Client Controller.

- CB N: Improvements due to changes in module communication.

- OCPP: Created singletons are now thread safe.

- OCPP: Completely decoupled from CB N and now only communicates with CB Master.

- OCPP: Simplified communication between modules.

- OCPP: Improvements due to changes in module communication.

- Pole: Created singletons are now thread safe.

- Pole: Completely decoupled CB N and we obtain all information needed in one call to CB Master.

- Pole: Improvements due to changes in module communication.

- CB Master: Client Controller won't stop sending messages and will show errors every 10 wrongly sent messages.

- CB Master: The charger now limits the number of messages that appear in the case that there's a range validation fail of a measure.

- CB N: Client Controller won't stop sending messages and will show errors every 10 wrongly sent messages.

- CB N: Restart Server Controller mechanism.

- OCPP: If there's an error handling a request, we won't add it to the offline queue.

- OCPP: Client Controller won't stop sending messages and will show errors every 10 wrongly sent messages.

- OCPP: Include thread and sys libraries.

- OCPP: Restart async Server Controller mechanism.

- Pole: Client Controller won't stop sending messages and will show errors every 10 wrongly sent messages.

- OCPP: When rebooting, we check module communication server.

- CB N: When rebooting, we check module communication server.

- CB N: Decoupled concept of connector id and measurer address.

- CB Master: When rebooting, we check module communication server.

- CB Master: Decoupled concept of connector id and measurer address.

- CB Master: Fixed error in Phoenix Contact measurer.

- Pole: ZMQ integrated to improve communication.

- Pole: Improvement to let the user know when to connect the vehicle.

- Pole: Screen now reflects if charger has only one connector.

- CB Master: Changed SSID format so that it's the same as Trydan's format.

- CB Master: Phoenix Contact measurer is now integrated.

- OCPP: Fixed problem with repeated logs.

- OCPP: AuthorizeRemoteTxRequests is now a read and write configuration key.

- OCPP: Fixed case when central station id is an integer.

- OCPP: Added measurer range validation.

- CB Master: Fixed problem with repeated logs.

- CB Master: Added measurer range validation.

- CB N: Fixed problem with repeated logs.

- CB Master: Access point can now change configuration of second connector if it has it.

- CB N: Handled special case of change intensity.

- CB N: OCPP Status Notification transitions fixed when there's an unavailable connector.

- CB N: If OCPP is on, we disable payment mode.

- CB Master: Access point logic fininshed.

- OCPP: Data validation when configuration is changed.

- OCPP: Charger can now handle multiple transactions offline.

- CB Master: Increased time before rebooting to improve stability.

- OCPP: Reset function improved. Corresponding Status Notification is sent.

- CB N: General stability improvements.

- CB N: Changed payment method approach.

- CB Master: Changed payment method approach.

- CB Master: Improved robustness in the case the access point software is not installed.

- Pole: We show device id on the screen.

- Pole: Improvements due to payment method.

- OCPP: Data transfer method to obtain logs.

- OCPP: Change availability validates connector.

- CB Master: Changed compressed file formats from gzip to gz

- CB Master: Force backup when restarting.

- CB Master: Finished Access point.

- CB N: Added set internal config function.

- CB N: Allow to change intensity, when i2c is failing.

- CB Master: Fixed OCPP measurer error that ocurred when all selected measures in Meter Values returned 0.

- CB Master: Implemented most of the access point server functionalities.

- CB Master: Initial version of the access point server.

- CB Master: If payment mode is active, charger won't allow to charge with RFID card.

- CB Master: Changes to improve Pole software.

- CB N: Changes to improve Pole software.

- Pole: Changes to simplify view logic.

- Pole: Removed sourceMappingUrl to prevent 404 error when there's no internet.

- CB N: Payment mode changed since payload format for server has changed.

- Pole: Changes in screen software that reflects payment mode, blocking connectors and OCPP.

OCPP: Fixed Unlock and Reset bug.

OCPP: Charger won't send Authorize if passed RFID card is already used in a transaction.

OCPP: We store RFID cards in lower caps to improve robustness.

- OCPP: Improved robustness of RFID cards stored in the Local Authorization list.

- OCPP: Authorization list works when there's no conection to the central system.

- OCPP: We handle key AllowOfflineTxForUnknownId.

- OCPP: Improved Local Authorization logic.

- OCPP: Fixed bugs from first integration test with EVIO.

- CB Master: Fixed wifilist sending format.

- CB Master: We report wifi_info and wifilist by direct method or bluetooth.

- CB N: We report information regarding wifi_info. Direct method to ask for the SSIDs the raspberry pi detects.

- OCPP: Improved authorization cache handler.

- OCPP: Improved request queue when there is no conection to central system.

- OCPP: Improved handling of measurer values.

- OCPP: Unlock connector implemented.

- OCPP: Improved handling of configuration keys.

- CB N: When the charger is initialized payment method will be off by default.

- CB N: Payment mode with duration and timers.

- CB Master: Function to obtain CPU temperature. It's a possible OCPP Meter Value.

- OCPP: Improved MeterValues handler.

- OCPP: Finished Local Authorization List profile.

- OCPP: Log Improvements.

- OCPP: Fixed bug that wouldn't send Authorize Request when passing the RFID card.

- OCPP: Offline queue implemented for Start Transaction.

- OCPP: Basic implementation of OCPP profiles: FirmwareManagement, LocalAuthListManagement, Reservation and SmartCharging.

- CB Master: Fixed RFID card reading with Wiegand reader for cards that have a 0 on the left side. Example of cards that failed: 32:0a:2c:23, 41:00:32:12.

- OCPP: Availability isn't managed by OCPP anymore. It is handled exclusively by property locked.

- OCPP: Boot Notification now send the charger model correctly.

- CB N: If charger is blocked, led blinks won't be sent.

- CB N: Payment Mode finished with start and stop.

- OCPP: Clear Cache can only be performed when all connectors are in the OCPP state Available.

- CB N: When property locked is changed, OCPP availability is also changed.

- OCPP: Changes so that availability can be changed from CB N.

- CB N: If OCPP is active, it reports Status Notification with its corresponding state.

- CB Master: OCPP module can now ask for Status Notification.

- OCPP: The charger the different possible OCPP states in the Status Notification.

- OCPP: We can now set configuration parameters for safeguard.

- OCPP: Change availability is now completely functional. It changes to inoperative during a charge and availability changes the locked value.

- OCPP: Changed way we obtain measurer data for OCPP.

- OCPP: Temporary fix for Place to plug since OCPP library can't handle unknown keys.

- OCPP: Fixed _available_connectors error.

- OCPP.

- Screen.

- Pole.

- CB Master.

- CB N.