Ενημερώσεις Pole Pro
Βελτιώνουμε συνεχώς τις λειτουργίες του φορτιστή Pole Pro. Εδώ θα βρείτε την πιο πρόσφατη έκδοση του e-Charger μας και τις τελευταίες ενημερώσεις που έχουν πραγματοποιηθεί.
Τελευταία έκδοση
6.1.3
Pole Pro
Έχετε το προηγούμενο Pole; Δείτε τις ενημερώσεις του.
6.1.3Τελευταία έκδοση
- ΔιόρθωσηThe charger no longer hangs when rebooting while shutting down the 4G module or dynamic power control
Προηγούμενες εκδόσεις 46
- 6.1.2ΔιόρθωσηOCPP security event notifications are no longer sent when the connection uses no security profile (profile 0), since some central systems do not support them
-
- ΔιόρθωσηCorrected default APN for Wireless Logic SIM cards in Belgium
-
- ΝέοAudible buzzer feedback
- ΝέοSupport for registering multiple RFID cards
- ΝέοReading of the installation meter over Modbus RS485 on DC chargers
- ΝέοDynamic power control for DC installations — master and slave units now share and honor the installation power limit
- ΝέοLive display of actual consumption versus offered current on the charger screen
- ΝέοOn-screen guidance walks the user through registering an RFID card
- ΝέοOCPP connection password can now be set from the Cloud and Bluetooth
- ΝέοOCPP now supports security profiles, encrypted TLS connections and Basic Authentication for the central system
- ΒελτίωσηLanguage codes standardized to the ISO 639-1 format
- ΒελτίωσηReduced volume of messages sent to the Cloud
- ΒελτίωσηTime synchronization with the CSMS no longer floods the system log
- ΒελτίωσηLog rotation no longer loses history when the disk is full
- ΒελτίωσηSafer firmware updates
- ΒελτίωσηMore reliable connectivity with automatic failover between Ethernet and 4G
- ΒελτίωσηCharges history now loads page by page instead of the whole history at once, for a faster tab
- ΔιόρθωσηMeasurer error message now reads clearly
- ΔιόρθωσηMore accurate meter-reading validation
- ΔιόρθωσηCharge metrics are preserved if a charge is interrupted unexpectedly
- ΔιόρθωσηScreen orientation set in configuration is now applied correctly
- ΔιόρθωσηFree-charge mode could not be disabled from the installer panel
- ΔιόρθωσηDynamic power limit was not applied at tariff/hour boundaries, briefly leaving an installation without a limit
- ΔιόρθωσηResolved random service restarts (crashes) caused by network device discovery
-
- ΒελτίωσηMore reliable RFID card reading with optimized antenna configuration from first use
- ΒελτίωσηImproved stability and responsiveness of the charger's web interface
-
- ΝέοOCPP - Immediate "Preparing" status when receiving a remote start command via OCPP
- ΝέοWiFi disabled by default on devices without WiFi configured
- ΒελτίωσηMore reliable RFID card reading with periodic reader reinitialization
- ΒελτίωσηBetter cable connection detection and RFID timeout handling
- ΒελτίωσηCDP - More stable network device discovery, preventing unnecessary register/unregister cycles
- ΒελτίωσηImproved stability when applying configuration changes to the charger
- ΒελτίωσηAutomatic migration of legacy pending OCPP messages after update
- ΒελτίωσηImproved network handling when switching between manual and automatic IP configuration
- ΔιόρθωσηPower factor value conversion for Carlo Gavazzi meters
- ΔιόρθωσηImprovements in power measurement accuracy in single-phase or two-phase installations
- ΔιόρθωσηOCPP - Smart Charging profiles with defined duration now applied correctly
- ΔιόρθωσηOCPP - Local authentication cache overflow that could prevent charging sessions from startIing
- ΔιόρθωσηOCPP - OCPP transactions stuck due to unreleased semaphores or null keys
-
- ΝέοEnhanced web server for accessing and editing charger properties
- ΝέοVisual improvements to the web server interface
- ΝέοPersistent price display on screen when the payment system is active
- ΝέοRefined error reporting to the cloud
- ΝέοPower loss detection
- ΝέοWi-Fi disable option from the installer panel
- ΝέοNew buzzer system implementation for white boards
- ΒελτίωσηEnhanced RFID calibration with on-screen indicator during the process
- ΒελτίωσηRFID reader no longer forcibly activates when OCPP or Payments are active; explicit configuration is respected
- ΒελτίωσηRefined cable connect/disconnect notification on each event when payments are active
- ΒελτίωσηOptimized RFID card readings
- ΒελτίωσηOCPP - Improvements to the offline transaction queue
- ΒελτίωσηInternal connection optimization and overall performance improvements
- ΔιόρθωσηOCPP - Improved measurement value reporting
- ΔιόρθωσηRefined out-of-range measurement error detection
-
- ΝέοSoftware-level leak detection enable/disable
- ΒελτίωσηAdjusted cooldown time between charges when a leak is detected
- ΒελτίωσηOCPP - Improvements to the offline transaction queue
-
- ΒελτίωσηWhen OCPP is active, we now show on screen when card passed is not registered in central system.
- ΔιόρθωσηAfter update OCPP image and QR is now recovered.
-
- ΔιόρθωσηFixed issue where it didn't allow a remote start if a car is connected but not in an active transaction.
- ΔιόρθωσηFixed issue in setup interface.
- ΔιόρθωσηFixed monophasic Carlo Gavazzi measurer.
- ΔιόρθωσηFixed OCPP issue where it wouldn't charge in connector 2 if connector 1 is charging.
-
- ΒελτίωσηImproved network features mainly 4G connection.
-
- ΒελτίωσηImproved OCPP charge handling.
- ΒελτίωσηEnhanced reliability in the smart charging logic.
- ΒελτίωσηImproved features when stopping a charge with invalid identifiers.
- ΒελτίωσηImproved QR configuration for OCPP.
- ΒελτίωσηImproved error handling when sensors or communication components fail.
- ΒελτίωσηBetter log management to prevent the device’s storage from filling up.
- ΒελτίωσηImproved USB connection features.
- ΒελτίωσηImproved RFID calibration and detection display.
- ΒελτίωσηImproved features related to Bluetooth.
- ΒελτίωσηImproved dynamic power control allowing charge at minimum intensity if master is not detected.
-
- ΝέοManual timezone setting is now available – The user will be able to configure the timezone even if automatic detection is disabled
- ΝέοCreated a contingency page in case app is not running
- ΝέοAdded Italian option for screen
- ΝέοAdded default payment QR to pay without app
- ΝέοAdded new OCPP personalization options - The user can now set 2 QR codes on the screen
- ΒελτίωσηImproved updater
- ΒελτίωσηImproved network connections
- ΒελτίωσηImproved OCPP meter values
- ΒελτίωσηImproved discovering devices when dynamic control is active
- ΒελτίωσηImproved user interface when updates are in progress
- ΒελτίωσηLocal load balancing is now implemented as dynamic control based specific conditions
- ΒελτίωσηImproved Bluetooth connection
- ΒελτίωσηImproved 4g connections robustness
- ΒελτίωσηImproved STM32 lock timings
- ΒελτίωσηImproved OCPP now allows external intensity limits
- ΒελτίωσηImproved data consumption
- ΔιόρθωσηWhen locking a connector while charging, it now sends end charge telemetry correctly
- ΔιόρθωσηFixed dynamic control issues
- ΔιόρθωσηFixed Carlo Gavazzi power meter
- ΔιόρθωσηFixed OCPP LMS, diagnostics, and charging profile clearing
-
- ΝέοAdded shared library
- ΝέοTimezone can be set manually
- ΝέοTime is now synced with Central System if OCPP is active
- ΒελτίωσηImproved version/update manager
- ΒελτίωσηImproved megabyte conversion of Network Monitor
- ΒελτίωσηObtaining timezone now doesn't need to have correct time by using only http urls
- ΒελτίωσηMobile usb device name is now obtained dynamically since more usb ports might be used due to TPV
- ΔιόρθωσηFixed power control issues
- ΔιόρθωσηFixed that when locking connector during a charge it now ends correctly
- ΔιόρθωσηRecalculate reboot time when changing time with ble
- ΔιόρθωσηWe now show on screen when non registered RFID is passed while OCPP is active
- ΔιόρθωσηFixed OCPP freemode rfid issues
- ΔιόρθωσηDuplicate StatusNotifications are removed from offline queue
- ΔιόρθωσηFixed "infinite" OCPP offline queue issue
-
- ΝέοAPN can now be set manually
- ΒελτίωσηWe now show on screen different wifi images depending on how strong signal is to let know the user how good the connection is
- ΒελτίωσηGeneral OCPP improvements: we check connection to CS instead of internet for local functioning, we notify a real value now when there's a stop transaction due to power loss, fixed edge cases where connectivity is lost, new ocpp key MaxEVCurrentOffered implemented which limits charge with key instead of smart charging handler, safety mechanisms for ocpp to be more robust
- ΒελτίωσηIn 4g, increased rssi range for "excellent" so that it indicates correctly when the reception is good
- ΒελτίωσηImproved data consumption
- ΒελτίωσηImproved robustness of update
- ΕνημέρωσηAccess point time increased to 15 minutes
- ΔιόρθωσηHandled issues when SSID has whitespace
-
- ΔιόρθωσηAccess point improvements.
- ΔιόρθωσηFixed QA issues.
-
- ΝέοNew direct method to obtain additional information for Smart Charging.
- ΝέοFixed random reboot time.
- ΒελτίωσηFixed unset RFID.
- ΒελτίωσηFixed Unknown measurer and made distinction between Unknown measurer and wrongly configured measurer.
- ΒελτίωσηOCPP Free mode can be toggled through OCPP keys.
- ΕνημέρωσηFixed BLE connection with iphone and fixed bluetooth communication error that appeared on app.
- ΕνημέρωσηNetwork improvements. No interface resets performed at boot which improves bootup time. Network changes now don't require reboot. When changing WIFI settings or ip ethernet settings, it connects after setting it instead of rebooting.
- ΔιόρθωσηFixed issue where things on screen were missing in one connector chargers.
- ΔιόρθωσηFixed time/timezone issue caused when the date is off by a few days.
- ΔιόρθωσηNew property added to toggle if vehicle should be able to charge even though measurers aren't working ( Only works when OCPP, payments or dynamic control isn't enabled ).
-
- ΝέοReflect on screen when charge is paused.
- ΝέοMade reboot time random.
- ΔιόρθωσηIncreased SAS token time to live of azure.
-
- ΝέοChanges made to reduce network usage that can be toggled on or off.
- ΝέοFixed case where config is corrupted or missing and would give trouble at startup.
- ΝέοWe now send dead letter if cpu gets too hot and cpu temperature is now logged.
- ΒελτίωσηFixed OCPP inverted measurer error.
- ΒελτίωσηAdded mechanism to disable or enable Wifi and bluetooth.
- ΒελτίωσηWe now report information regarding which type of connection to the internet the e-charger has.
- ΕνημέρωσηChanged led colors. Switched State A (now white) and State B (now green) colors.
- ΔιόρθωσηFixed set threshold values and neopixel leds of Stm32. We can now also obtain control pilot value from Stm32.
- ΔιόρθωσηOCPP ConnectionTimeOut value can now be changed on the fly.
- ΔιόρθωσηWe now report iccid of sim card is connected. If sim is connected but we can't obtain iccid, we send dead letter.
- ΔιόρθωσηFixed log download of http interface.
-
- ΝέοLTE signal is now reflected correctly instead of always showing great signal.
- ΒελτίωσηFixed wathdog reboot after doing hard reset.
-
- ΝέοAdded dynamic photovoltaic.
- ΝέοAdded dead letters: measurer fails and kernel error.
- ΝέοProperty "wifi_info" is now reported.
- ΝέοProperty "wifi_static" can be set through ble.
- ΝέοWe can now obtain statistics through direct method.
- ΝέοAdded individual log level for each type of logger.
- ΝέοAdded neopixel led type for stm32.
- ΝέοWe can now set threshold values with stm32 and get control pilot value if debug log of "Stm32" is activated.
- ΒελτίωσηImprovements in dynamic control, fabrication, QA, Azure, OCPP, config handling, 4g, access point and stm32.
- ΒελτίωσηWe now obtain timezone through url.
- ΒελτίωσηRemoved raspbian logo and desktop during boot and added V2C logo.
- ΒελτίωσηChanged default language after fabrication from english to spanish.
- ΕνημέρωσηGeneral bug fixes.
- ΔιόρθωσηWhen downgrading we ensure that version we downgrade to is compatible.
-
- ΝέοFixed property "ocpp" change bug.
- ΒελτίωσηProperties "powerweekday", "powerweekend" and "phase_map" can be changed through bluetooth.
- ΒελτίωσηChanged configuration handling to differentiate internally and externally set variables so that externally set or obtained variables are handled accordingly following the property schemas.
- ΔιόρθωσηWe now report wifi_static with static ip configuration.
- ΔιόρθωσηStatistics are now saved locally.
-
- ΒελτίωσηMeasurer fails are now registered with modbusrtumeasurer.
- ΒελτίωσηScreen font bigger for small title.
- ΔιόρθωσηValidate configuration with schemas during loading.
-
- ΝέοOCPP authorize can now function by connector.
- ΝέοOCPP WSS connection.
- ΝέοFixed OCPP parent id tag bug.
- ΝέοOCPP meter values now work for 3 phases.
- ΒελτίωσηFixed error 3 not appearing on screen.
- ΒελτίωσηFixed energy by hour bug.
- ΒελτίωσηChanged measurer reading approach for faster reads.
- ΒελτίωσηWith dynamic balancing we now show used and available power in frontend.
-
- ΒελτίωσηWe show dynamic balancing information on screen.
- ΒελτίωσηSimplified handling of configuration.
- ΒελτίωσηImproved dynamic balancing.
-
- ΒελτίωσηCharger won't reboot if car is in state B and OCPP or Payments is active.
- ΒελτίωσηWhen car changes from state C to B, charge information will persist on screen.
- ΒελτίωσηCurrent state charge now reports errors.
- ΒελτίωσηAdded configuration property validation.
- ΔιόρθωσηDirect method to obtain dynamic balancing information.
- ΔιόρθωσηGeneral dynamic balancing improvements.
- ΔιόρθωσηOCPP improvements.
-
- ΔιόρθωσηChanged remaining set_basic_unreported_config to set_basic_config.
-
- ΝέοFix dynamic control bug, powerbytram is not being updated.
- ΝέοFixed bug where whitelist of reported items wasn't being applied and properties weren't being stored in database.
- ΒελτίωσηRemoved non-repetitive logger.
- ΒελτίωσηChanged access point interface to change apn, with manual mode or mobile operator mode.
- ΕνημέρωσηRefactored config charge box. Removed BASIC_UNREPORTED and created whitelist of properties to report.
- ΕνημέρωσηPhase map is now not applied to installation meters.
- ΔιόρθωσηFixed payment bug where a charge couldn't be started properly if charge was started with the hose unlocked.
- ΔιόρθωσηFix bug with power being zero, dynamic control failing when there are no connectors.
- 3.1.8ΕνημέρωσηForce WIFI and bluetooth GPIO pins for compute module 4 to work.
- 3.1.7ΕνημέρωσηForce 4g GPIO pins for compute module 4 to work.
-
- ΒελτίωσηWhen we detect that measurers aren't working, we send an unblock command in case there's a charge and the charger has lost power.
- ΒελτίωσηCreate section BASIC_UNREPORTED for properties that are used but we don't want to report.
- ΒελτίωσηLocked value has persistance when measurers fail.
- ΔιόρθωσηWhen we don't receive petitions from chromium we now press enter and Ctrl+F5 if there's anything we need to accept.
-
- ΔιόρθωσηChanging WIFI configuration with bluetooth now reboots the charge point.
-
- ΒελτίωσηFixed configuration file so that software works with compute module 3 and 4.
- ΒελτίωσηChanged reboot logic. It will now reboot if there's a car connected but charge is not allowed.
- ΔιόρθωσηChanged payments qr code.
- ΔιόρθωσηWe can change log level with property.
-
- ΔιόρθωσηMeter values fixed. We now send wh instead of kwh.
-
- ΝέοPause is now reset when it goes back to state A.
- ΝέοShow measurer error as "Error 3" on connector. Behaviour is that connector is locked until it's fixed.
- ΝέοSet wire connected again.
- ΒελτίωσηFixed general network errors. Improved access point and wifi connectivity.
- ΔιόρθωσηFixed error where timezone wasn't set correctly so time appeared incorrectly.
- ΔιόρθωσηFixed payment_max_mode timeout bug.
-
- ΝέοFixed power, it was shown in W and is now in Kw.
- ΒελτίωσηChange timezone automatically.
- ΔιόρθωσηAdded triphasic phoenix contact measurer.
- ΑφαίρεσηFixed removal of grey notification update.
-
- ΝέοWhenever there's an action that provokes rebooting, it will show on screen that it's going to reboot and the cause.
- ΝέοScreen orientation can now be set and depending on parameter.
- ΝέοAdded error message 1 and 2.
- ΝέοBluetooth patch so that bluetooth initialization takes less time.
- ΝέοCreated patch system. System level changes will be applied with this system.
- ΒελτίωσηMeasurer refactoring.
- ΒελτίωσηImei obtention improved.
- ΒελτίωσηInitial version of bluetooth finished: Obtain properties change basic properties, program charge, reboot, add rfid and change wifi.
- ΒελτίωσηBoot improvements. "Page not found" isn't shown anymore. Boot is faster. There's a gif indicating that system is starting.
- ΒελτίωσηObsolete properties are now deleted automatically so that they aren't reported.
- ΕνημέρωσηRFID can now function with payments. If RFID is enabled with payments, registered cards will be able to start charges. If RFID is disabled with payments, no card will be able to start a charge.
- ΔιόρθωσηLimited number of messages we can send to iothub.
- ΔιόρθωσηIn OCPP, fixed sending of meter values. Now sending in wh and not in kwh.
- ΔιόρθωσηBoot patch so that GPIO pin initialization takes less time.
- ΔιόρθωσηMonophasic measurer Eastron SDM220 implemented.
- ΔιόρθωσηImproved robustness on all direct methods.
- ΔιόρθωσηFixed bug where it didn't reconnect properly to iothub when it disconnected.
- ΔιόρθωσηCreated direct method to put a QR code on the OCPP screen.
- ΑφαίρεσηRemoved wire_connected event telemetry.
- 3.0.9ΔιόρθωσηFixed ocpp meter value Energy.Active.Import, when measurer is flipped.
-
- ΕνημέρωσηFixed error where e-Charger couldn't obtain dns when connected with WIFI.
- ΔιόρθωσηFixed local load balancing when one connector was charging. Now when one connector is charging, it will charge at the set intensity.
- 3.0.7ΔιόρθωσηFixed ocpp Remote Start Transaction and Remote Stop Transaction.
- 3.0.6ΔιόρθωσηFixed error that ocurred in ocpp where it didn't clear properly the idtag when finishing a transaction.
-
- ΕνημέρωσηChanged access point ip from 192.168.44.1 to 192.168.4.1
- ΕνημέρωσηWe now report the charger's state instead of the requested vehicle state.
- ΕνημέρωσηChanged access point master password.
- ΔιόρθωσηFixed websocket connection issue with nuitka compilation.
-
- ΒελτίωσηImproved update logs.
- 3.0.3ΝέοMoved Version from center to right side and added V. before the version number.
- 3.0.2ΒελτίωσηSTM will now detect SPI bus communication errors and will automatically reset.
-
- ΝέοScreen now shows when RFID card is registered.
- ΝέοTop bar now shows version and if access point is accessible.
- ΝέοAccess point interface now has, local load balancing, rfid card registering and log download.
- ΝέοCheck that compute module and board have been created properly.
- ΒελτίωσηScreen is now monitored so that it refreshes in the case that no requests have been made after 15 seconds.
- ΒελτίωσηQA diagnostic is obtained through access point.
- ΒελτίωσηReduced access point available time to 10 minutes.
- ΔιόρθωσηFixed bug where connector stopped working properly when sending intensity 0.
-
- ΝέοInitial Version
6 από 46