Updates voor Pole Pro
Wij werken continu aan het verbeteren van de functionaliteiten van Pole Pro. Hier vindt u de meest recente versie van onze e-Charger en de laatste updates die zijn doorgevoerd.
Nieuwste versie
6.1.3
Pole Pro
Heeft u de vorige Pole? Bekijk de updates ervan.
6.1.3Nieuwste versie
- OpgelostThe charger no longer hangs when rebooting while shutting down the 4G module or dynamic power control
Eerdere versies 46
- 6.1.2OpgelostOCPP security event notifications are no longer sent when the connection uses no security profile (profile 0), since some central systems do not support them
-
- OpgelostCorrected default APN for Wireless Logic SIM cards in Belgium
-
- NieuwAudible buzzer feedback
- NieuwSupport for registering multiple RFID cards
- NieuwReading of the installation meter over Modbus RS485 on DC chargers
- NieuwDynamic power control for DC installations — master and slave units now share and honor the installation power limit
- NieuwLive display of actual consumption versus offered current on the charger screen
- NieuwOn-screen guidance walks the user through registering an RFID card
- NieuwOCPP connection password can now be set from the Cloud and Bluetooth
- NieuwOCPP now supports security profiles, encrypted TLS connections and Basic Authentication for the central system
- VerbeterdLanguage codes standardized to the ISO 639-1 format
- VerbeterdReduced volume of messages sent to the Cloud
- VerbeterdTime synchronization with the CSMS no longer floods the system log
- VerbeterdLog rotation no longer loses history when the disk is full
- VerbeterdSafer firmware updates
- VerbeterdMore reliable connectivity with automatic failover between Ethernet and 4G
- VerbeterdCharges history now loads page by page instead of the whole history at once, for a faster tab
- OpgelostMeasurer error message now reads clearly
- OpgelostMore accurate meter-reading validation
- OpgelostCharge metrics are preserved if a charge is interrupted unexpectedly
- OpgelostScreen orientation set in configuration is now applied correctly
- OpgelostFree-charge mode could not be disabled from the installer panel
- OpgelostDynamic power limit was not applied at tariff/hour boundaries, briefly leaving an installation without a limit
- OpgelostResolved random service restarts (crashes) caused by network device discovery
-
- VerbeterdMore reliable RFID card reading with optimized antenna configuration from first use
- VerbeterdImproved stability and responsiveness of the charger's web interface
-
- NieuwOCPP - Immediate "Preparing" status when receiving a remote start command via OCPP
- NieuwWiFi disabled by default on devices without WiFi configured
- VerbeterdMore reliable RFID card reading with periodic reader reinitialization
- VerbeterdBetter cable connection detection and RFID timeout handling
- VerbeterdCDP - More stable network device discovery, preventing unnecessary register/unregister cycles
- VerbeterdImproved stability when applying configuration changes to the charger
- VerbeterdAutomatic migration of legacy pending OCPP messages after update
- VerbeterdImproved network handling when switching between manual and automatic IP configuration
- OpgelostPower factor value conversion for Carlo Gavazzi meters
- OpgelostImprovements in power measurement accuracy in single-phase or two-phase installations
- OpgelostOCPP - Smart Charging profiles with defined duration now applied correctly
- OpgelostOCPP - Local authentication cache overflow that could prevent charging sessions from startIing
- OpgelostOCPP - OCPP transactions stuck due to unreleased semaphores or null keys
-
- NieuwEnhanced web server for accessing and editing charger properties
- NieuwVisual improvements to the web server interface
- NieuwPersistent price display on screen when the payment system is active
- NieuwRefined error reporting to the cloud
- NieuwPower loss detection
- NieuwWi-Fi disable option from the installer panel
- NieuwNew buzzer system implementation for white boards
- VerbeterdEnhanced RFID calibration with on-screen indicator during the process
- VerbeterdRFID reader no longer forcibly activates when OCPP or Payments are active; explicit configuration is respected
- VerbeterdRefined cable connect/disconnect notification on each event when payments are active
- VerbeterdOptimized RFID card readings
- VerbeterdOCPP - Improvements to the offline transaction queue
- VerbeterdInternal connection optimization and overall performance improvements
- OpgelostOCPP - Improved measurement value reporting
- OpgelostRefined out-of-range measurement error detection
-
- NieuwSoftware-level leak detection enable/disable
- VerbeterdAdjusted cooldown time between charges when a leak is detected
- VerbeterdOCPP - Improvements to the offline transaction queue
-
- VerbeterdWhen OCPP is active, we now show on screen when card passed is not registered in central system.
- OpgelostAfter update OCPP image and QR is now recovered.
-
- OpgelostFixed issue where it didn't allow a remote start if a car is connected but not in an active transaction.
- OpgelostFixed issue in setup interface.
- OpgelostFixed monophasic Carlo Gavazzi measurer.
- OpgelostFixed OCPP issue where it wouldn't charge in connector 2 if connector 1 is charging.
-
- VerbeterdImproved network features mainly 4G connection.
-
- VerbeterdImproved OCPP charge handling.
- VerbeterdEnhanced reliability in the smart charging logic.
- VerbeterdImproved features when stopping a charge with invalid identifiers.
- VerbeterdImproved QR configuration for OCPP.
- VerbeterdImproved error handling when sensors or communication components fail.
- VerbeterdBetter log management to prevent the device’s storage from filling up.
- VerbeterdImproved USB connection features.
- VerbeterdImproved RFID calibration and detection display.
- VerbeterdImproved features related to Bluetooth.
- VerbeterdImproved dynamic power control allowing charge at minimum intensity if master is not detected.
-
- NieuwManual timezone setting is now available – The user will be able to configure the timezone even if automatic detection is disabled
- NieuwCreated a contingency page in case app is not running
- NieuwAdded Italian option for screen
- NieuwAdded default payment QR to pay without app
- NieuwAdded new OCPP personalization options - The user can now set 2 QR codes on the screen
- VerbeterdImproved updater
- VerbeterdImproved network connections
- VerbeterdImproved OCPP meter values
- VerbeterdImproved discovering devices when dynamic control is active
- VerbeterdImproved user interface when updates are in progress
- VerbeterdLocal load balancing is now implemented as dynamic control based specific conditions
- VerbeterdImproved Bluetooth connection
- VerbeterdImproved 4g connections robustness
- VerbeterdImproved STM32 lock timings
- VerbeterdImproved OCPP now allows external intensity limits
- VerbeterdImproved data consumption
- OpgelostWhen locking a connector while charging, it now sends end charge telemetry correctly
- OpgelostFixed dynamic control issues
- OpgelostFixed Carlo Gavazzi power meter
- OpgelostFixed OCPP LMS, diagnostics, and charging profile clearing
-
- NieuwAdded shared library
- NieuwTimezone can be set manually
- NieuwTime is now synced with Central System if OCPP is active
- VerbeterdImproved version/update manager
- VerbeterdImproved megabyte conversion of Network Monitor
- VerbeterdObtaining timezone now doesn't need to have correct time by using only http urls
- VerbeterdMobile usb device name is now obtained dynamically since more usb ports might be used due to TPV
- OpgelostFixed power control issues
- OpgelostFixed that when locking connector during a charge it now ends correctly
- OpgelostRecalculate reboot time when changing time with ble
- OpgelostWe now show on screen when non registered RFID is passed while OCPP is active
- OpgelostFixed OCPP freemode rfid issues
- OpgelostDuplicate StatusNotifications are removed from offline queue
- OpgelostFixed "infinite" OCPP offline queue issue
-
- NieuwAPN can now be set manually
- VerbeterdWe now show on screen different wifi images depending on how strong signal is to let know the user how good the connection is
- VerbeterdGeneral OCPP improvements: we check connection to CS instead of internet for local functioning, we notify a real value now when there's a stop transaction due to power loss, fixed edge cases where connectivity is lost, new ocpp key MaxEVCurrentOffered implemented which limits charge with key instead of smart charging handler, safety mechanisms for ocpp to be more robust
- VerbeterdIn 4g, increased rssi range for "excellent" so that it indicates correctly when the reception is good
- VerbeterdImproved data consumption
- VerbeterdImproved robustness of update
- BijgewerktAccess point time increased to 15 minutes
- OpgelostHandled issues when SSID has whitespace
-
- OpgelostAccess point improvements.
- OpgelostFixed QA issues.
-
- NieuwNew direct method to obtain additional information for Smart Charging.
- NieuwFixed random reboot time.
- VerbeterdFixed unset RFID.
- VerbeterdFixed Unknown measurer and made distinction between Unknown measurer and wrongly configured measurer.
- VerbeterdOCPP Free mode can be toggled through OCPP keys.
- BijgewerktFixed BLE connection with iphone and fixed bluetooth communication error that appeared on app.
- BijgewerktNetwork improvements. No interface resets performed at boot which improves bootup time. Network changes now don't require reboot. When changing WIFI settings or ip ethernet settings, it connects after setting it instead of rebooting.
- OpgelostFixed issue where things on screen were missing in one connector chargers.
- OpgelostFixed time/timezone issue caused when the date is off by a few days.
- OpgelostNew property added to toggle if vehicle should be able to charge even though measurers aren't working ( Only works when OCPP, payments or dynamic control isn't enabled ).
-
- NieuwReflect on screen when charge is paused.
- NieuwMade reboot time random.
- OpgelostIncreased SAS token time to live of azure.
-
- NieuwChanges made to reduce network usage that can be toggled on or off.
- NieuwFixed case where config is corrupted or missing and would give trouble at startup.
- NieuwWe now send dead letter if cpu gets too hot and cpu temperature is now logged.
- VerbeterdFixed OCPP inverted measurer error.
- VerbeterdAdded mechanism to disable or enable Wifi and bluetooth.
- VerbeterdWe now report information regarding which type of connection to the internet the e-charger has.
- BijgewerktChanged led colors. Switched State A (now white) and State B (now green) colors.
- OpgelostFixed set threshold values and neopixel leds of Stm32. We can now also obtain control pilot value from Stm32.
- OpgelostOCPP ConnectionTimeOut value can now be changed on the fly.
- OpgelostWe now report iccid of sim card is connected. If sim is connected but we can't obtain iccid, we send dead letter.
- OpgelostFixed log download of http interface.
-
- NieuwLTE signal is now reflected correctly instead of always showing great signal.
- VerbeterdFixed wathdog reboot after doing hard reset.
-
- NieuwAdded dynamic photovoltaic.
- NieuwAdded dead letters: measurer fails and kernel error.
- NieuwProperty "wifi_info" is now reported.
- NieuwProperty "wifi_static" can be set through ble.
- NieuwWe can now obtain statistics through direct method.
- NieuwAdded individual log level for each type of logger.
- NieuwAdded neopixel led type for stm32.
- NieuwWe can now set threshold values with stm32 and get control pilot value if debug log of "Stm32" is activated.
- VerbeterdImprovements in dynamic control, fabrication, QA, Azure, OCPP, config handling, 4g, access point and stm32.
- VerbeterdWe now obtain timezone through url.
- VerbeterdRemoved raspbian logo and desktop during boot and added V2C logo.
- VerbeterdChanged default language after fabrication from english to spanish.
- BijgewerktGeneral bug fixes.
- OpgelostWhen downgrading we ensure that version we downgrade to is compatible.
-
- NieuwFixed property "ocpp" change bug.
- VerbeterdProperties "powerweekday", "powerweekend" and "phase_map" can be changed through bluetooth.
- VerbeterdChanged configuration handling to differentiate internally and externally set variables so that externally set or obtained variables are handled accordingly following the property schemas.
- OpgelostWe now report wifi_static with static ip configuration.
- OpgelostStatistics are now saved locally.
-
- VerbeterdMeasurer fails are now registered with modbusrtumeasurer.
- VerbeterdScreen font bigger for small title.
- OpgelostValidate configuration with schemas during loading.
-
- NieuwOCPP authorize can now function by connector.
- NieuwOCPP WSS connection.
- NieuwFixed OCPP parent id tag bug.
- NieuwOCPP meter values now work for 3 phases.
- VerbeterdFixed error 3 not appearing on screen.
- VerbeterdFixed energy by hour bug.
- VerbeterdChanged measurer reading approach for faster reads.
- VerbeterdWith dynamic balancing we now show used and available power in frontend.
-
- VerbeterdWe show dynamic balancing information on screen.
- VerbeterdSimplified handling of configuration.
- VerbeterdImproved dynamic balancing.
-
- VerbeterdCharger won't reboot if car is in state B and OCPP or Payments is active.
- VerbeterdWhen car changes from state C to B, charge information will persist on screen.
- VerbeterdCurrent state charge now reports errors.
- VerbeterdAdded configuration property validation.
- OpgelostDirect method to obtain dynamic balancing information.
- OpgelostGeneral dynamic balancing improvements.
- OpgelostOCPP improvements.
-
- OpgelostChanged remaining set_basic_unreported_config to set_basic_config.
-
- NieuwFix dynamic control bug, powerbytram is not being updated.
- NieuwFixed bug where whitelist of reported items wasn't being applied and properties weren't being stored in database.
- VerbeterdRemoved non-repetitive logger.
- VerbeterdChanged access point interface to change apn, with manual mode or mobile operator mode.
- BijgewerktRefactored config charge box. Removed BASIC_UNREPORTED and created whitelist of properties to report.
- BijgewerktPhase map is now not applied to installation meters.
- OpgelostFixed payment bug where a charge couldn't be started properly if charge was started with the hose unlocked.
- OpgelostFix bug with power being zero, dynamic control failing when there are no connectors.
- 3.1.8BijgewerktForce WIFI and bluetooth GPIO pins for compute module 4 to work.
- 3.1.7BijgewerktForce 4g GPIO pins for compute module 4 to work.
-
- VerbeterdWhen we detect that measurers aren't working, we send an unblock command in case there's a charge and the charger has lost power.
- VerbeterdCreate section BASIC_UNREPORTED for properties that are used but we don't want to report.
- VerbeterdLocked value has persistance when measurers fail.
- OpgelostWhen we don't receive petitions from chromium we now press enter and Ctrl+F5 if there's anything we need to accept.
-
- OpgelostChanging WIFI configuration with bluetooth now reboots the charge point.
-
- VerbeterdFixed configuration file so that software works with compute module 3 and 4.
- VerbeterdChanged reboot logic. It will now reboot if there's a car connected but charge is not allowed.
- OpgelostChanged payments qr code.
- OpgelostWe can change log level with property.
-
- OpgelostMeter values fixed. We now send wh instead of kwh.
-
- NieuwPause is now reset when it goes back to state A.
- NieuwShow measurer error as "Error 3" on connector. Behaviour is that connector is locked until it's fixed.
- NieuwSet wire connected again.
- VerbeterdFixed general network errors. Improved access point and wifi connectivity.
- OpgelostFixed error where timezone wasn't set correctly so time appeared incorrectly.
- OpgelostFixed payment_max_mode timeout bug.
-
- NieuwFixed power, it was shown in W and is now in Kw.
- VerbeterdChange timezone automatically.
- OpgelostAdded triphasic phoenix contact measurer.
- VerwijderdFixed removal of grey notification update.
-
- NieuwWhenever there's an action that provokes rebooting, it will show on screen that it's going to reboot and the cause.
- NieuwScreen orientation can now be set and depending on parameter.
- NieuwAdded error message 1 and 2.
- NieuwBluetooth patch so that bluetooth initialization takes less time.
- NieuwCreated patch system. System level changes will be applied with this system.
- VerbeterdMeasurer refactoring.
- VerbeterdImei obtention improved.
- VerbeterdInitial version of bluetooth finished: Obtain properties change basic properties, program charge, reboot, add rfid and change wifi.
- VerbeterdBoot improvements. "Page not found" isn't shown anymore. Boot is faster. There's a gif indicating that system is starting.
- VerbeterdObsolete properties are now deleted automatically so that they aren't reported.
- BijgewerktRFID can now function with payments. If RFID is enabled with payments, registered cards will be able to start charges. If RFID is disabled with payments, no card will be able to start a charge.
- OpgelostLimited number of messages we can send to iothub.
- OpgelostIn OCPP, fixed sending of meter values. Now sending in wh and not in kwh.
- OpgelostBoot patch so that GPIO pin initialization takes less time.
- OpgelostMonophasic measurer Eastron SDM220 implemented.
- OpgelostImproved robustness on all direct methods.
- OpgelostFixed bug where it didn't reconnect properly to iothub when it disconnected.
- OpgelostCreated direct method to put a QR code on the OCPP screen.
- VerwijderdRemoved wire_connected event telemetry.
- 3.0.9OpgelostFixed ocpp meter value Energy.Active.Import, when measurer is flipped.
-
- BijgewerktFixed error where e-Charger couldn't obtain dns when connected with WIFI.
- OpgelostFixed local load balancing when one connector was charging. Now when one connector is charging, it will charge at the set intensity.
- 3.0.7OpgelostFixed ocpp Remote Start Transaction and Remote Stop Transaction.
- 3.0.6OpgelostFixed error that ocurred in ocpp where it didn't clear properly the idtag when finishing a transaction.
-
- BijgewerktChanged access point ip from 192.168.44.1 to 192.168.4.1
- BijgewerktWe now report the charger's state instead of the requested vehicle state.
- BijgewerktChanged access point master password.
- OpgelostFixed websocket connection issue with nuitka compilation.
-
- VerbeterdImproved update logs.
- 3.0.3NieuwMoved Version from center to right side and added V. before the version number.
- 3.0.2VerbeterdSTM will now detect SPI bus communication errors and will automatically reset.
-
- NieuwScreen now shows when RFID card is registered.
- NieuwTop bar now shows version and if access point is accessible.
- NieuwAccess point interface now has, local load balancing, rfid card registering and log download.
- NieuwCheck that compute module and board have been created properly.
- VerbeterdScreen is now monitored so that it refreshes in the case that no requests have been made after 15 seconds.
- VerbeterdQA diagnostic is obtained through access point.
- VerbeterdReduced access point available time to 10 minutes.
- OpgelostFixed bug where connector stopped working properly when sending intensity 0.
-
- NieuwInitial Version
6 van 46