Aktualizacje Pole Pro
Nieustannie pracujemy nad rozwojem funkcji ładowarki Pole Pro. Tutaj znajdziesz najnowszą wersję naszego e-Chargera i ostatnio wprowadzone aktualizacje.
Najnowsza wersja
6.1.3
Pole Pro
Masz poprzedni Pole? Zobacz jego aktualizacje.
6.1.3Najnowsza wersja
- PoprawkaThe charger no longer hangs when rebooting while shutting down the 4G module or dynamic power control
Wcześniejsze wersje 46
- 6.1.2PoprawkaOCPP security event notifications are no longer sent when the connection uses no security profile (profile 0), since some central systems do not support them
-
- PoprawkaCorrected default APN for Wireless Logic SIM cards in Belgium
-
- NowośćAudible buzzer feedback
- NowośćSupport for registering multiple RFID cards
- NowośćReading of the installation meter over Modbus RS485 on DC chargers
- NowośćDynamic power control for DC installations — master and slave units now share and honor the installation power limit
- NowośćLive display of actual consumption versus offered current on the charger screen
- NowośćOn-screen guidance walks the user through registering an RFID card
- NowośćOCPP connection password can now be set from the Cloud and Bluetooth
- NowośćOCPP now supports security profiles, encrypted TLS connections and Basic Authentication for the central system
- UlepszenieLanguage codes standardized to the ISO 639-1 format
- UlepszenieReduced volume of messages sent to the Cloud
- UlepszenieTime synchronization with the CSMS no longer floods the system log
- UlepszenieLog rotation no longer loses history when the disk is full
- UlepszenieSafer firmware updates
- UlepszenieMore reliable connectivity with automatic failover between Ethernet and 4G
- UlepszenieCharges history now loads page by page instead of the whole history at once, for a faster tab
- PoprawkaMeasurer error message now reads clearly
- PoprawkaMore accurate meter-reading validation
- PoprawkaCharge metrics are preserved if a charge is interrupted unexpectedly
- PoprawkaScreen orientation set in configuration is now applied correctly
- PoprawkaFree-charge mode could not be disabled from the installer panel
- PoprawkaDynamic power limit was not applied at tariff/hour boundaries, briefly leaving an installation without a limit
- PoprawkaResolved random service restarts (crashes) caused by network device discovery
-
- UlepszenieMore reliable RFID card reading with optimized antenna configuration from first use
- UlepszenieImproved stability and responsiveness of the charger's web interface
-
- NowośćOCPP - Immediate "Preparing" status when receiving a remote start command via OCPP
- NowośćWiFi disabled by default on devices without WiFi configured
- UlepszenieMore reliable RFID card reading with periodic reader reinitialization
- UlepszenieBetter cable connection detection and RFID timeout handling
- UlepszenieCDP - More stable network device discovery, preventing unnecessary register/unregister cycles
- UlepszenieImproved stability when applying configuration changes to the charger
- UlepszenieAutomatic migration of legacy pending OCPP messages after update
- UlepszenieImproved network handling when switching between manual and automatic IP configuration
- PoprawkaPower factor value conversion for Carlo Gavazzi meters
- PoprawkaImprovements in power measurement accuracy in single-phase or two-phase installations
- PoprawkaOCPP - Smart Charging profiles with defined duration now applied correctly
- PoprawkaOCPP - Local authentication cache overflow that could prevent charging sessions from startIing
- PoprawkaOCPP - OCPP transactions stuck due to unreleased semaphores or null keys
-
- NowośćEnhanced web server for accessing and editing charger properties
- NowośćVisual improvements to the web server interface
- NowośćPersistent price display on screen when the payment system is active
- NowośćRefined error reporting to the cloud
- NowośćPower loss detection
- NowośćWi-Fi disable option from the installer panel
- NowośćNew buzzer system implementation for white boards
- UlepszenieEnhanced RFID calibration with on-screen indicator during the process
- UlepszenieRFID reader no longer forcibly activates when OCPP or Payments are active; explicit configuration is respected
- UlepszenieRefined cable connect/disconnect notification on each event when payments are active
- UlepszenieOptimized RFID card readings
- UlepszenieOCPP - Improvements to the offline transaction queue
- UlepszenieInternal connection optimization and overall performance improvements
- PoprawkaOCPP - Improved measurement value reporting
- PoprawkaRefined out-of-range measurement error detection
-
- NowośćSoftware-level leak detection enable/disable
- UlepszenieAdjusted cooldown time between charges when a leak is detected
- UlepszenieOCPP - Improvements to the offline transaction queue
-
- UlepszenieWhen OCPP is active, we now show on screen when card passed is not registered in central system.
- PoprawkaAfter update OCPP image and QR is now recovered.
-
- PoprawkaFixed issue where it didn't allow a remote start if a car is connected but not in an active transaction.
- PoprawkaFixed issue in setup interface.
- PoprawkaFixed monophasic Carlo Gavazzi measurer.
- PoprawkaFixed OCPP issue where it wouldn't charge in connector 2 if connector 1 is charging.
-
- UlepszenieImproved network features mainly 4G connection.
-
- UlepszenieImproved OCPP charge handling.
- UlepszenieEnhanced reliability in the smart charging logic.
- UlepszenieImproved features when stopping a charge with invalid identifiers.
- UlepszenieImproved QR configuration for OCPP.
- UlepszenieImproved error handling when sensors or communication components fail.
- UlepszenieBetter log management to prevent the device’s storage from filling up.
- UlepszenieImproved USB connection features.
- UlepszenieImproved RFID calibration and detection display.
- UlepszenieImproved features related to Bluetooth.
- UlepszenieImproved dynamic power control allowing charge at minimum intensity if master is not detected.
-
- NowośćManual timezone setting is now available – The user will be able to configure the timezone even if automatic detection is disabled
- NowośćCreated a contingency page in case app is not running
- NowośćAdded Italian option for screen
- NowośćAdded default payment QR to pay without app
- NowośćAdded new OCPP personalization options - The user can now set 2 QR codes on the screen
- UlepszenieImproved updater
- UlepszenieImproved network connections
- UlepszenieImproved OCPP meter values
- UlepszenieImproved discovering devices when dynamic control is active
- UlepszenieImproved user interface when updates are in progress
- UlepszenieLocal load balancing is now implemented as dynamic control based specific conditions
- UlepszenieImproved Bluetooth connection
- UlepszenieImproved 4g connections robustness
- UlepszenieImproved STM32 lock timings
- UlepszenieImproved OCPP now allows external intensity limits
- UlepszenieImproved data consumption
- PoprawkaWhen locking a connector while charging, it now sends end charge telemetry correctly
- PoprawkaFixed dynamic control issues
- PoprawkaFixed Carlo Gavazzi power meter
- PoprawkaFixed OCPP LMS, diagnostics, and charging profile clearing
-
- NowośćAdded shared library
- NowośćTimezone can be set manually
- NowośćTime is now synced with Central System if OCPP is active
- UlepszenieImproved version/update manager
- UlepszenieImproved megabyte conversion of Network Monitor
- UlepszenieObtaining timezone now doesn't need to have correct time by using only http urls
- UlepszenieMobile usb device name is now obtained dynamically since more usb ports might be used due to TPV
- PoprawkaFixed power control issues
- PoprawkaFixed that when locking connector during a charge it now ends correctly
- PoprawkaRecalculate reboot time when changing time with ble
- PoprawkaWe now show on screen when non registered RFID is passed while OCPP is active
- PoprawkaFixed OCPP freemode rfid issues
- PoprawkaDuplicate StatusNotifications are removed from offline queue
- PoprawkaFixed "infinite" OCPP offline queue issue
-
- NowośćAPN can now be set manually
- UlepszenieWe now show on screen different wifi images depending on how strong signal is to let know the user how good the connection is
- UlepszenieGeneral OCPP improvements: we check connection to CS instead of internet for local functioning, we notify a real value now when there's a stop transaction due to power loss, fixed edge cases where connectivity is lost, new ocpp key MaxEVCurrentOffered implemented which limits charge with key instead of smart charging handler, safety mechanisms for ocpp to be more robust
- UlepszenieIn 4g, increased rssi range for "excellent" so that it indicates correctly when the reception is good
- UlepszenieImproved data consumption
- UlepszenieImproved robustness of update
- ZaktualizowanoAccess point time increased to 15 minutes
- PoprawkaHandled issues when SSID has whitespace
-
- PoprawkaAccess point improvements.
- PoprawkaFixed QA issues.
-
- NowośćNew direct method to obtain additional information for Smart Charging.
- NowośćFixed random reboot time.
- UlepszenieFixed unset RFID.
- UlepszenieFixed Unknown measurer and made distinction between Unknown measurer and wrongly configured measurer.
- UlepszenieOCPP Free mode can be toggled through OCPP keys.
- ZaktualizowanoFixed BLE connection with iphone and fixed bluetooth communication error that appeared on app.
- ZaktualizowanoNetwork improvements. No interface resets performed at boot which improves bootup time. Network changes now don't require reboot. When changing WIFI settings or ip ethernet settings, it connects after setting it instead of rebooting.
- PoprawkaFixed issue where things on screen were missing in one connector chargers.
- PoprawkaFixed time/timezone issue caused when the date is off by a few days.
- PoprawkaNew property added to toggle if vehicle should be able to charge even though measurers aren't working ( Only works when OCPP, payments or dynamic control isn't enabled ).
-
- NowośćReflect on screen when charge is paused.
- NowośćMade reboot time random.
- PoprawkaIncreased SAS token time to live of azure.
-
- NowośćChanges made to reduce network usage that can be toggled on or off.
- NowośćFixed case where config is corrupted or missing and would give trouble at startup.
- NowośćWe now send dead letter if cpu gets too hot and cpu temperature is now logged.
- UlepszenieFixed OCPP inverted measurer error.
- UlepszenieAdded mechanism to disable or enable Wifi and bluetooth.
- UlepszenieWe now report information regarding which type of connection to the internet the e-charger has.
- ZaktualizowanoChanged led colors. Switched State A (now white) and State B (now green) colors.
- PoprawkaFixed set threshold values and neopixel leds of Stm32. We can now also obtain control pilot value from Stm32.
- PoprawkaOCPP ConnectionTimeOut value can now be changed on the fly.
- PoprawkaWe now report iccid of sim card is connected. If sim is connected but we can't obtain iccid, we send dead letter.
- PoprawkaFixed log download of http interface.
-
- NowośćLTE signal is now reflected correctly instead of always showing great signal.
- UlepszenieFixed wathdog reboot after doing hard reset.
-
- NowośćAdded dynamic photovoltaic.
- NowośćAdded dead letters: measurer fails and kernel error.
- NowośćProperty "wifi_info" is now reported.
- NowośćProperty "wifi_static" can be set through ble.
- NowośćWe can now obtain statistics through direct method.
- NowośćAdded individual log level for each type of logger.
- NowośćAdded neopixel led type for stm32.
- NowośćWe can now set threshold values with stm32 and get control pilot value if debug log of "Stm32" is activated.
- UlepszenieImprovements in dynamic control, fabrication, QA, Azure, OCPP, config handling, 4g, access point and stm32.
- UlepszenieWe now obtain timezone through url.
- UlepszenieRemoved raspbian logo and desktop during boot and added V2C logo.
- UlepszenieChanged default language after fabrication from english to spanish.
- ZaktualizowanoGeneral bug fixes.
- PoprawkaWhen downgrading we ensure that version we downgrade to is compatible.
-
- NowośćFixed property "ocpp" change bug.
- UlepszenieProperties "powerweekday", "powerweekend" and "phase_map" can be changed through bluetooth.
- UlepszenieChanged configuration handling to differentiate internally and externally set variables so that externally set or obtained variables are handled accordingly following the property schemas.
- PoprawkaWe now report wifi_static with static ip configuration.
- PoprawkaStatistics are now saved locally.
-
- UlepszenieMeasurer fails are now registered with modbusrtumeasurer.
- UlepszenieScreen font bigger for small title.
- PoprawkaValidate configuration with schemas during loading.
-
- NowośćOCPP authorize can now function by connector.
- NowośćOCPP WSS connection.
- NowośćFixed OCPP parent id tag bug.
- NowośćOCPP meter values now work for 3 phases.
- UlepszenieFixed error 3 not appearing on screen.
- UlepszenieFixed energy by hour bug.
- UlepszenieChanged measurer reading approach for faster reads.
- UlepszenieWith dynamic balancing we now show used and available power in frontend.
-
- UlepszenieWe show dynamic balancing information on screen.
- UlepszenieSimplified handling of configuration.
- UlepszenieImproved dynamic balancing.
-
- UlepszenieCharger won't reboot if car is in state B and OCPP or Payments is active.
- UlepszenieWhen car changes from state C to B, charge information will persist on screen.
- UlepszenieCurrent state charge now reports errors.
- UlepszenieAdded configuration property validation.
- PoprawkaDirect method to obtain dynamic balancing information.
- PoprawkaGeneral dynamic balancing improvements.
- PoprawkaOCPP improvements.
-
- PoprawkaChanged remaining set_basic_unreported_config to set_basic_config.
-
- NowośćFix dynamic control bug, powerbytram is not being updated.
- NowośćFixed bug where whitelist of reported items wasn't being applied and properties weren't being stored in database.
- UlepszenieRemoved non-repetitive logger.
- UlepszenieChanged access point interface to change apn, with manual mode or mobile operator mode.
- ZaktualizowanoRefactored config charge box. Removed BASIC_UNREPORTED and created whitelist of properties to report.
- ZaktualizowanoPhase map is now not applied to installation meters.
- PoprawkaFixed payment bug where a charge couldn't be started properly if charge was started with the hose unlocked.
- PoprawkaFix bug with power being zero, dynamic control failing when there are no connectors.
- 3.1.8ZaktualizowanoForce WIFI and bluetooth GPIO pins for compute module 4 to work.
- 3.1.7ZaktualizowanoForce 4g GPIO pins for compute module 4 to work.
-
- UlepszenieWhen we detect that measurers aren't working, we send an unblock command in case there's a charge and the charger has lost power.
- UlepszenieCreate section BASIC_UNREPORTED for properties that are used but we don't want to report.
- UlepszenieLocked value has persistance when measurers fail.
- PoprawkaWhen we don't receive petitions from chromium we now press enter and Ctrl+F5 if there's anything we need to accept.
-
- PoprawkaChanging WIFI configuration with bluetooth now reboots the charge point.
-
- UlepszenieFixed configuration file so that software works with compute module 3 and 4.
- UlepszenieChanged reboot logic. It will now reboot if there's a car connected but charge is not allowed.
- PoprawkaChanged payments qr code.
- PoprawkaWe can change log level with property.
-
- PoprawkaMeter values fixed. We now send wh instead of kwh.
-
- NowośćPause is now reset when it goes back to state A.
- NowośćShow measurer error as "Error 3" on connector. Behaviour is that connector is locked until it's fixed.
- NowośćSet wire connected again.
- UlepszenieFixed general network errors. Improved access point and wifi connectivity.
- PoprawkaFixed error where timezone wasn't set correctly so time appeared incorrectly.
- PoprawkaFixed payment_max_mode timeout bug.
-
- NowośćFixed power, it was shown in W and is now in Kw.
- UlepszenieChange timezone automatically.
- PoprawkaAdded triphasic phoenix contact measurer.
- UsuniętoFixed removal of grey notification update.
-
- NowośćWhenever there's an action that provokes rebooting, it will show on screen that it's going to reboot and the cause.
- NowośćScreen orientation can now be set and depending on parameter.
- NowośćAdded error message 1 and 2.
- NowośćBluetooth patch so that bluetooth initialization takes less time.
- NowośćCreated patch system. System level changes will be applied with this system.
- UlepszenieMeasurer refactoring.
- UlepszenieImei obtention improved.
- UlepszenieInitial version of bluetooth finished: Obtain properties change basic properties, program charge, reboot, add rfid and change wifi.
- UlepszenieBoot improvements. "Page not found" isn't shown anymore. Boot is faster. There's a gif indicating that system is starting.
- UlepszenieObsolete properties are now deleted automatically so that they aren't reported.
- ZaktualizowanoRFID can now function with payments. If RFID is enabled with payments, registered cards will be able to start charges. If RFID is disabled with payments, no card will be able to start a charge.
- PoprawkaLimited number of messages we can send to iothub.
- PoprawkaIn OCPP, fixed sending of meter values. Now sending in wh and not in kwh.
- PoprawkaBoot patch so that GPIO pin initialization takes less time.
- PoprawkaMonophasic measurer Eastron SDM220 implemented.
- PoprawkaImproved robustness on all direct methods.
- PoprawkaFixed bug where it didn't reconnect properly to iothub when it disconnected.
- PoprawkaCreated direct method to put a QR code on the OCPP screen.
- UsuniętoRemoved wire_connected event telemetry.
- 3.0.9PoprawkaFixed ocpp meter value Energy.Active.Import, when measurer is flipped.
-
- ZaktualizowanoFixed error where e-Charger couldn't obtain dns when connected with WIFI.
- PoprawkaFixed local load balancing when one connector was charging. Now when one connector is charging, it will charge at the set intensity.
- 3.0.7PoprawkaFixed ocpp Remote Start Transaction and Remote Stop Transaction.
- 3.0.6PoprawkaFixed error that ocurred in ocpp where it didn't clear properly the idtag when finishing a transaction.
-
- ZaktualizowanoChanged access point ip from 192.168.44.1 to 192.168.4.1
- ZaktualizowanoWe now report the charger's state instead of the requested vehicle state.
- ZaktualizowanoChanged access point master password.
- PoprawkaFixed websocket connection issue with nuitka compilation.
-
- UlepszenieImproved update logs.
- 3.0.3NowośćMoved Version from center to right side and added V. before the version number.
- 3.0.2UlepszenieSTM will now detect SPI bus communication errors and will automatically reset.
-
- NowośćScreen now shows when RFID card is registered.
- NowośćTop bar now shows version and if access point is accessible.
- NowośćAccess point interface now has, local load balancing, rfid card registering and log download.
- NowośćCheck that compute module and board have been created properly.
- UlepszenieScreen is now monitored so that it refreshes in the case that no requests have been made after 15 seconds.
- UlepszenieQA diagnostic is obtained through access point.
- UlepszenieReduced access point available time to 10 minutes.
- PoprawkaFixed bug where connector stopped working properly when sending intensity 0.
-
- NowośćInitial Version
6 z 46