Aktualizace pro Pole Pro
Neustále pracujeme na zlepšování funkcí nabíječky Pole Pro. Zde najdete nejnovější verzi naší nabíječky e-Charger a nejnovější provedené aktualizace.
Nejnovější verze
6.1.3
Pole Pro
Máte předchozí Pole? Podívejte se na jeho aktualizace.
6.1.3Nejnovější verze
- OpravaThe charger no longer hangs when rebooting while shutting down the 4G module or dynamic power control
Starší verze 46
- 6.1.2OpravaOCPP security event notifications are no longer sent when the connection uses no security profile (profile 0), since some central systems do not support them
-
- OpravaCorrected default APN for Wireless Logic SIM cards in Belgium
-
- NovinkaAudible buzzer feedback
- NovinkaSupport for registering multiple RFID cards
- NovinkaReading of the installation meter over Modbus RS485 on DC chargers
- NovinkaDynamic power control for DC installations — master and slave units now share and honor the installation power limit
- NovinkaLive display of actual consumption versus offered current on the charger screen
- NovinkaOn-screen guidance walks the user through registering an RFID card
- NovinkaOCPP connection password can now be set from the Cloud and Bluetooth
- NovinkaOCPP now supports security profiles, encrypted TLS connections and Basic Authentication for the central system
- VylepšeníLanguage codes standardized to the ISO 639-1 format
- VylepšeníReduced volume of messages sent to the Cloud
- VylepšeníTime synchronization with the CSMS no longer floods the system log
- VylepšeníLog rotation no longer loses history when the disk is full
- VylepšeníSafer firmware updates
- VylepšeníMore reliable connectivity with automatic failover between Ethernet and 4G
- VylepšeníCharges history now loads page by page instead of the whole history at once, for a faster tab
- OpravaMeasurer error message now reads clearly
- OpravaMore accurate meter-reading validation
- OpravaCharge metrics are preserved if a charge is interrupted unexpectedly
- OpravaScreen orientation set in configuration is now applied correctly
- OpravaFree-charge mode could not be disabled from the installer panel
- OpravaDynamic power limit was not applied at tariff/hour boundaries, briefly leaving an installation without a limit
- OpravaResolved random service restarts (crashes) caused by network device discovery
-
- VylepšeníMore reliable RFID card reading with optimized antenna configuration from first use
- VylepšeníImproved stability and responsiveness of the charger's web interface
-
- NovinkaOCPP - Immediate "Preparing" status when receiving a remote start command via OCPP
- NovinkaWiFi disabled by default on devices without WiFi configured
- VylepšeníMore reliable RFID card reading with periodic reader reinitialization
- VylepšeníBetter cable connection detection and RFID timeout handling
- VylepšeníCDP - More stable network device discovery, preventing unnecessary register/unregister cycles
- VylepšeníImproved stability when applying configuration changes to the charger
- VylepšeníAutomatic migration of legacy pending OCPP messages after update
- VylepšeníImproved network handling when switching between manual and automatic IP configuration
- OpravaPower factor value conversion for Carlo Gavazzi meters
- OpravaImprovements in power measurement accuracy in single-phase or two-phase installations
- OpravaOCPP - Smart Charging profiles with defined duration now applied correctly
- OpravaOCPP - Local authentication cache overflow that could prevent charging sessions from startIing
- OpravaOCPP - OCPP transactions stuck due to unreleased semaphores or null keys
-
- NovinkaEnhanced web server for accessing and editing charger properties
- NovinkaVisual improvements to the web server interface
- NovinkaPersistent price display on screen when the payment system is active
- NovinkaRefined error reporting to the cloud
- NovinkaPower loss detection
- NovinkaWi-Fi disable option from the installer panel
- NovinkaNew buzzer system implementation for white boards
- VylepšeníEnhanced RFID calibration with on-screen indicator during the process
- VylepšeníRFID reader no longer forcibly activates when OCPP or Payments are active; explicit configuration is respected
- VylepšeníRefined cable connect/disconnect notification on each event when payments are active
- VylepšeníOptimized RFID card readings
- VylepšeníOCPP - Improvements to the offline transaction queue
- VylepšeníInternal connection optimization and overall performance improvements
- OpravaOCPP - Improved measurement value reporting
- OpravaRefined out-of-range measurement error detection
-
- NovinkaSoftware-level leak detection enable/disable
- VylepšeníAdjusted cooldown time between charges when a leak is detected
- VylepšeníOCPP - Improvements to the offline transaction queue
-
- VylepšeníWhen OCPP is active, we now show on screen when card passed is not registered in central system.
- OpravaAfter update OCPP image and QR is now recovered.
-
- OpravaFixed issue where it didn't allow a remote start if a car is connected but not in an active transaction.
- OpravaFixed issue in setup interface.
- OpravaFixed monophasic Carlo Gavazzi measurer.
- OpravaFixed OCPP issue where it wouldn't charge in connector 2 if connector 1 is charging.
-
- VylepšeníImproved network features mainly 4G connection.
-
- VylepšeníImproved OCPP charge handling.
- VylepšeníEnhanced reliability in the smart charging logic.
- VylepšeníImproved features when stopping a charge with invalid identifiers.
- VylepšeníImproved QR configuration for OCPP.
- VylepšeníImproved error handling when sensors or communication components fail.
- VylepšeníBetter log management to prevent the device’s storage from filling up.
- VylepšeníImproved USB connection features.
- VylepšeníImproved RFID calibration and detection display.
- VylepšeníImproved features related to Bluetooth.
- VylepšeníImproved dynamic power control allowing charge at minimum intensity if master is not detected.
-
- NovinkaManual timezone setting is now available – The user will be able to configure the timezone even if automatic detection is disabled
- NovinkaCreated a contingency page in case app is not running
- NovinkaAdded Italian option for screen
- NovinkaAdded default payment QR to pay without app
- NovinkaAdded new OCPP personalization options - The user can now set 2 QR codes on the screen
- VylepšeníImproved updater
- VylepšeníImproved network connections
- VylepšeníImproved OCPP meter values
- VylepšeníImproved discovering devices when dynamic control is active
- VylepšeníImproved user interface when updates are in progress
- VylepšeníLocal load balancing is now implemented as dynamic control based specific conditions
- VylepšeníImproved Bluetooth connection
- VylepšeníImproved 4g connections robustness
- VylepšeníImproved STM32 lock timings
- VylepšeníImproved OCPP now allows external intensity limits
- VylepšeníImproved data consumption
- OpravaWhen locking a connector while charging, it now sends end charge telemetry correctly
- OpravaFixed dynamic control issues
- OpravaFixed Carlo Gavazzi power meter
- OpravaFixed OCPP LMS, diagnostics, and charging profile clearing
-
- NovinkaAdded shared library
- NovinkaTimezone can be set manually
- NovinkaTime is now synced with Central System if OCPP is active
- VylepšeníImproved version/update manager
- VylepšeníImproved megabyte conversion of Network Monitor
- VylepšeníObtaining timezone now doesn't need to have correct time by using only http urls
- VylepšeníMobile usb device name is now obtained dynamically since more usb ports might be used due to TPV
- OpravaFixed power control issues
- OpravaFixed that when locking connector during a charge it now ends correctly
- OpravaRecalculate reboot time when changing time with ble
- OpravaWe now show on screen when non registered RFID is passed while OCPP is active
- OpravaFixed OCPP freemode rfid issues
- OpravaDuplicate StatusNotifications are removed from offline queue
- OpravaFixed "infinite" OCPP offline queue issue
-
- NovinkaAPN can now be set manually
- VylepšeníWe now show on screen different wifi images depending on how strong signal is to let know the user how good the connection is
- VylepšeníGeneral OCPP improvements: we check connection to CS instead of internet for local functioning, we notify a real value now when there's a stop transaction due to power loss, fixed edge cases where connectivity is lost, new ocpp key MaxEVCurrentOffered implemented which limits charge with key instead of smart charging handler, safety mechanisms for ocpp to be more robust
- VylepšeníIn 4g, increased rssi range for "excellent" so that it indicates correctly when the reception is good
- VylepšeníImproved data consumption
- VylepšeníImproved robustness of update
- AktualizovánoAccess point time increased to 15 minutes
- OpravaHandled issues when SSID has whitespace
-
- OpravaAccess point improvements.
- OpravaFixed QA issues.
-
- NovinkaNew direct method to obtain additional information for Smart Charging.
- NovinkaFixed random reboot time.
- VylepšeníFixed unset RFID.
- VylepšeníFixed Unknown measurer and made distinction between Unknown measurer and wrongly configured measurer.
- VylepšeníOCPP Free mode can be toggled through OCPP keys.
- AktualizovánoFixed BLE connection with iphone and fixed bluetooth communication error that appeared on app.
- AktualizovánoNetwork improvements. No interface resets performed at boot which improves bootup time. Network changes now don't require reboot. When changing WIFI settings or ip ethernet settings, it connects after setting it instead of rebooting.
- OpravaFixed issue where things on screen were missing in one connector chargers.
- OpravaFixed time/timezone issue caused when the date is off by a few days.
- OpravaNew property added to toggle if vehicle should be able to charge even though measurers aren't working ( Only works when OCPP, payments or dynamic control isn't enabled ).
-
- NovinkaReflect on screen when charge is paused.
- NovinkaMade reboot time random.
- OpravaIncreased SAS token time to live of azure.
-
- NovinkaChanges made to reduce network usage that can be toggled on or off.
- NovinkaFixed case where config is corrupted or missing and would give trouble at startup.
- NovinkaWe now send dead letter if cpu gets too hot and cpu temperature is now logged.
- VylepšeníFixed OCPP inverted measurer error.
- VylepšeníAdded mechanism to disable or enable Wifi and bluetooth.
- VylepšeníWe now report information regarding which type of connection to the internet the e-charger has.
- AktualizovánoChanged led colors. Switched State A (now white) and State B (now green) colors.
- OpravaFixed set threshold values and neopixel leds of Stm32. We can now also obtain control pilot value from Stm32.
- OpravaOCPP ConnectionTimeOut value can now be changed on the fly.
- OpravaWe now report iccid of sim card is connected. If sim is connected but we can't obtain iccid, we send dead letter.
- OpravaFixed log download of http interface.
-
- NovinkaLTE signal is now reflected correctly instead of always showing great signal.
- VylepšeníFixed wathdog reboot after doing hard reset.
-
- NovinkaAdded dynamic photovoltaic.
- NovinkaAdded dead letters: measurer fails and kernel error.
- NovinkaProperty "wifi_info" is now reported.
- NovinkaProperty "wifi_static" can be set through ble.
- NovinkaWe can now obtain statistics through direct method.
- NovinkaAdded individual log level for each type of logger.
- NovinkaAdded neopixel led type for stm32.
- NovinkaWe can now set threshold values with stm32 and get control pilot value if debug log of "Stm32" is activated.
- VylepšeníImprovements in dynamic control, fabrication, QA, Azure, OCPP, config handling, 4g, access point and stm32.
- VylepšeníWe now obtain timezone through url.
- VylepšeníRemoved raspbian logo and desktop during boot and added V2C logo.
- VylepšeníChanged default language after fabrication from english to spanish.
- AktualizovánoGeneral bug fixes.
- OpravaWhen downgrading we ensure that version we downgrade to is compatible.
-
- NovinkaFixed property "ocpp" change bug.
- VylepšeníProperties "powerweekday", "powerweekend" and "phase_map" can be changed through bluetooth.
- VylepšeníChanged configuration handling to differentiate internally and externally set variables so that externally set or obtained variables are handled accordingly following the property schemas.
- OpravaWe now report wifi_static with static ip configuration.
- OpravaStatistics are now saved locally.
-
- VylepšeníMeasurer fails are now registered with modbusrtumeasurer.
- VylepšeníScreen font bigger for small title.
- OpravaValidate configuration with schemas during loading.
-
- NovinkaOCPP authorize can now function by connector.
- NovinkaOCPP WSS connection.
- NovinkaFixed OCPP parent id tag bug.
- NovinkaOCPP meter values now work for 3 phases.
- VylepšeníFixed error 3 not appearing on screen.
- VylepšeníFixed energy by hour bug.
- VylepšeníChanged measurer reading approach for faster reads.
- VylepšeníWith dynamic balancing we now show used and available power in frontend.
-
- VylepšeníWe show dynamic balancing information on screen.
- VylepšeníSimplified handling of configuration.
- VylepšeníImproved dynamic balancing.
-
- VylepšeníCharger won't reboot if car is in state B and OCPP or Payments is active.
- VylepšeníWhen car changes from state C to B, charge information will persist on screen.
- VylepšeníCurrent state charge now reports errors.
- VylepšeníAdded configuration property validation.
- OpravaDirect method to obtain dynamic balancing information.
- OpravaGeneral dynamic balancing improvements.
- OpravaOCPP improvements.
-
- OpravaChanged remaining set_basic_unreported_config to set_basic_config.
-
- NovinkaFix dynamic control bug, powerbytram is not being updated.
- NovinkaFixed bug where whitelist of reported items wasn't being applied and properties weren't being stored in database.
- VylepšeníRemoved non-repetitive logger.
- VylepšeníChanged access point interface to change apn, with manual mode or mobile operator mode.
- AktualizovánoRefactored config charge box. Removed BASIC_UNREPORTED and created whitelist of properties to report.
- AktualizovánoPhase map is now not applied to installation meters.
- OpravaFixed payment bug where a charge couldn't be started properly if charge was started with the hose unlocked.
- OpravaFix bug with power being zero, dynamic control failing when there are no connectors.
- 3.1.8AktualizovánoForce WIFI and bluetooth GPIO pins for compute module 4 to work.
- 3.1.7AktualizovánoForce 4g GPIO pins for compute module 4 to work.
-
- VylepšeníWhen we detect that measurers aren't working, we send an unblock command in case there's a charge and the charger has lost power.
- VylepšeníCreate section BASIC_UNREPORTED for properties that are used but we don't want to report.
- VylepšeníLocked value has persistance when measurers fail.
- OpravaWhen we don't receive petitions from chromium we now press enter and Ctrl+F5 if there's anything we need to accept.
-
- OpravaChanging WIFI configuration with bluetooth now reboots the charge point.
-
- VylepšeníFixed configuration file so that software works with compute module 3 and 4.
- VylepšeníChanged reboot logic. It will now reboot if there's a car connected but charge is not allowed.
- OpravaChanged payments qr code.
- OpravaWe can change log level with property.
-
- OpravaMeter values fixed. We now send wh instead of kwh.
-
- NovinkaPause is now reset when it goes back to state A.
- NovinkaShow measurer error as "Error 3" on connector. Behaviour is that connector is locked until it's fixed.
- NovinkaSet wire connected again.
- VylepšeníFixed general network errors. Improved access point and wifi connectivity.
- OpravaFixed error where timezone wasn't set correctly so time appeared incorrectly.
- OpravaFixed payment_max_mode timeout bug.
-
- NovinkaFixed power, it was shown in W and is now in Kw.
- VylepšeníChange timezone automatically.
- OpravaAdded triphasic phoenix contact measurer.
- OdstraněnoFixed removal of grey notification update.
-
- NovinkaWhenever there's an action that provokes rebooting, it will show on screen that it's going to reboot and the cause.
- NovinkaScreen orientation can now be set and depending on parameter.
- NovinkaAdded error message 1 and 2.
- NovinkaBluetooth patch so that bluetooth initialization takes less time.
- NovinkaCreated patch system. System level changes will be applied with this system.
- VylepšeníMeasurer refactoring.
- VylepšeníImei obtention improved.
- VylepšeníInitial version of bluetooth finished: Obtain properties change basic properties, program charge, reboot, add rfid and change wifi.
- VylepšeníBoot improvements. "Page not found" isn't shown anymore. Boot is faster. There's a gif indicating that system is starting.
- VylepšeníObsolete properties are now deleted automatically so that they aren't reported.
- AktualizovánoRFID can now function with payments. If RFID is enabled with payments, registered cards will be able to start charges. If RFID is disabled with payments, no card will be able to start a charge.
- OpravaLimited number of messages we can send to iothub.
- OpravaIn OCPP, fixed sending of meter values. Now sending in wh and not in kwh.
- OpravaBoot patch so that GPIO pin initialization takes less time.
- OpravaMonophasic measurer Eastron SDM220 implemented.
- OpravaImproved robustness on all direct methods.
- OpravaFixed bug where it didn't reconnect properly to iothub when it disconnected.
- OpravaCreated direct method to put a QR code on the OCPP screen.
- OdstraněnoRemoved wire_connected event telemetry.
- 3.0.9OpravaFixed ocpp meter value Energy.Active.Import, when measurer is flipped.
-
- AktualizovánoFixed error where e-Charger couldn't obtain dns when connected with WIFI.
- OpravaFixed local load balancing when one connector was charging. Now when one connector is charging, it will charge at the set intensity.
- 3.0.7OpravaFixed ocpp Remote Start Transaction and Remote Stop Transaction.
- 3.0.6OpravaFixed error that ocurred in ocpp where it didn't clear properly the idtag when finishing a transaction.
-
- AktualizovánoChanged access point ip from 192.168.44.1 to 192.168.4.1
- AktualizovánoWe now report the charger's state instead of the requested vehicle state.
- AktualizovánoChanged access point master password.
- OpravaFixed websocket connection issue with nuitka compilation.
-
- VylepšeníImproved update logs.
- 3.0.3NovinkaMoved Version from center to right side and added V. before the version number.
- 3.0.2VylepšeníSTM will now detect SPI bus communication errors and will automatically reset.
-
- NovinkaScreen now shows when RFID card is registered.
- NovinkaTop bar now shows version and if access point is accessible.
- NovinkaAccess point interface now has, local load balancing, rfid card registering and log download.
- NovinkaCheck that compute module and board have been created properly.
- VylepšeníScreen is now monitored so that it refreshes in the case that no requests have been made after 15 seconds.
- VylepšeníQA diagnostic is obtained through access point.
- VylepšeníReduced access point available time to 10 minutes.
- OpravaFixed bug where connector stopped working properly when sending intensity 0.
-
- NovinkaInitial Version
6 z 46