Mises à jour Pole Pro
Nous travaillons en continu pour améliorer les fonctionnalités de Pole Pro. Vous trouverez ici la version la plus récente de notre e-Charger et les dernières mises à jour effectuées.
Dernière version
6.1.3
Pole Pro
Vous avez l'ancien Pole ? Consultez ses mises à jour.
6.1.3Dernière version
- CorrectionThe charger no longer hangs when rebooting while shutting down the 4G module or dynamic power control
Versions précédentes 46
- 6.1.2CorrectionOCPP security event notifications are no longer sent when the connection uses no security profile (profile 0), since some central systems do not support them
-
- CorrectionCorrected default APN for Wireless Logic SIM cards in Belgium
-
- NouveauAudible buzzer feedback
- NouveauSupport for registering multiple RFID cards
- NouveauReading of the installation meter over Modbus RS485 on DC chargers
- NouveauDynamic power control for DC installations — master and slave units now share and honor the installation power limit
- NouveauLive display of actual consumption versus offered current on the charger screen
- NouveauOn-screen guidance walks the user through registering an RFID card
- NouveauOCPP connection password can now be set from the Cloud and Bluetooth
- NouveauOCPP now supports security profiles, encrypted TLS connections and Basic Authentication for the central system
- AméliorationLanguage codes standardized to the ISO 639-1 format
- AméliorationReduced volume of messages sent to the Cloud
- AméliorationTime synchronization with the CSMS no longer floods the system log
- AméliorationLog rotation no longer loses history when the disk is full
- AméliorationSafer firmware updates
- AméliorationMore reliable connectivity with automatic failover between Ethernet and 4G
- AméliorationCharges history now loads page by page instead of the whole history at once, for a faster tab
- CorrectionMeasurer error message now reads clearly
- CorrectionMore accurate meter-reading validation
- CorrectionCharge metrics are preserved if a charge is interrupted unexpectedly
- CorrectionScreen orientation set in configuration is now applied correctly
- CorrectionFree-charge mode could not be disabled from the installer panel
- CorrectionDynamic power limit was not applied at tariff/hour boundaries, briefly leaving an installation without a limit
- CorrectionResolved random service restarts (crashes) caused by network device discovery
-
- AméliorationMore reliable RFID card reading with optimized antenna configuration from first use
- AméliorationImproved stability and responsiveness of the charger's web interface
-
- NouveauOCPP - Immediate "Preparing" status when receiving a remote start command via OCPP
- NouveauWiFi disabled by default on devices without WiFi configured
- AméliorationMore reliable RFID card reading with periodic reader reinitialization
- AméliorationBetter cable connection detection and RFID timeout handling
- AméliorationCDP - More stable network device discovery, preventing unnecessary register/unregister cycles
- AméliorationImproved stability when applying configuration changes to the charger
- AméliorationAutomatic migration of legacy pending OCPP messages after update
- AméliorationImproved network handling when switching between manual and automatic IP configuration
- CorrectionPower factor value conversion for Carlo Gavazzi meters
- CorrectionImprovements in power measurement accuracy in single-phase or two-phase installations
- CorrectionOCPP - Smart Charging profiles with defined duration now applied correctly
- CorrectionOCPP - Local authentication cache overflow that could prevent charging sessions from startIing
- CorrectionOCPP - OCPP transactions stuck due to unreleased semaphores or null keys
-
- NouveauEnhanced web server for accessing and editing charger properties
- NouveauVisual improvements to the web server interface
- NouveauPersistent price display on screen when the payment system is active
- NouveauRefined error reporting to the cloud
- NouveauPower loss detection
- NouveauWi-Fi disable option from the installer panel
- NouveauNew buzzer system implementation for white boards
- AméliorationEnhanced RFID calibration with on-screen indicator during the process
- AméliorationRFID reader no longer forcibly activates when OCPP or Payments are active; explicit configuration is respected
- AméliorationRefined cable connect/disconnect notification on each event when payments are active
- AméliorationOptimized RFID card readings
- AméliorationOCPP - Improvements to the offline transaction queue
- AméliorationInternal connection optimization and overall performance improvements
- CorrectionOCPP - Improved measurement value reporting
- CorrectionRefined out-of-range measurement error detection
-
- NouveauSoftware-level leak detection enable/disable
- AméliorationAdjusted cooldown time between charges when a leak is detected
- AméliorationOCPP - Improvements to the offline transaction queue
-
- AméliorationWhen OCPP is active, we now show on screen when card passed is not registered in central system.
- CorrectionAfter update OCPP image and QR is now recovered.
-
- CorrectionFixed issue where it didn't allow a remote start if a car is connected but not in an active transaction.
- CorrectionFixed issue in setup interface.
- CorrectionFixed monophasic Carlo Gavazzi measurer.
- CorrectionFixed OCPP issue where it wouldn't charge in connector 2 if connector 1 is charging.
-
- AméliorationImproved network features mainly 4G connection.
-
- AméliorationImproved OCPP charge handling.
- AméliorationEnhanced reliability in the smart charging logic.
- AméliorationImproved features when stopping a charge with invalid identifiers.
- AméliorationImproved QR configuration for OCPP.
- AméliorationImproved error handling when sensors or communication components fail.
- AméliorationBetter log management to prevent the device’s storage from filling up.
- AméliorationImproved USB connection features.
- AméliorationImproved RFID calibration and detection display.
- AméliorationImproved features related to Bluetooth.
- AméliorationImproved dynamic power control allowing charge at minimum intensity if master is not detected.
-
- NouveauManual timezone setting is now available – The user will be able to configure the timezone even if automatic detection is disabled
- NouveauCreated a contingency page in case app is not running
- NouveauAdded Italian option for screen
- NouveauAdded default payment QR to pay without app
- NouveauAdded new OCPP personalization options - The user can now set 2 QR codes on the screen
- AméliorationImproved updater
- AméliorationImproved network connections
- AméliorationImproved OCPP meter values
- AméliorationImproved discovering devices when dynamic control is active
- AméliorationImproved user interface when updates are in progress
- AméliorationLocal load balancing is now implemented as dynamic control based specific conditions
- AméliorationImproved Bluetooth connection
- AméliorationImproved 4g connections robustness
- AméliorationImproved STM32 lock timings
- AméliorationImproved OCPP now allows external intensity limits
- AméliorationImproved data consumption
- CorrectionWhen locking a connector while charging, it now sends end charge telemetry correctly
- CorrectionFixed dynamic control issues
- CorrectionFixed Carlo Gavazzi power meter
- CorrectionFixed OCPP LMS, diagnostics, and charging profile clearing
-
- NouveauAdded shared library
- NouveauTimezone can be set manually
- NouveauTime is now synced with Central System if OCPP is active
- AméliorationImproved version/update manager
- AméliorationImproved megabyte conversion of Network Monitor
- AméliorationObtaining timezone now doesn't need to have correct time by using only http urls
- AméliorationMobile usb device name is now obtained dynamically since more usb ports might be used due to TPV
- CorrectionFixed power control issues
- CorrectionFixed that when locking connector during a charge it now ends correctly
- CorrectionRecalculate reboot time when changing time with ble
- CorrectionWe now show on screen when non registered RFID is passed while OCPP is active
- CorrectionFixed OCPP freemode rfid issues
- CorrectionDuplicate StatusNotifications are removed from offline queue
- CorrectionFixed "infinite" OCPP offline queue issue
-
- NouveauAPN can now be set manually
- AméliorationWe now show on screen different wifi images depending on how strong signal is to let know the user how good the connection is
- AméliorationGeneral OCPP improvements: we check connection to CS instead of internet for local functioning, we notify a real value now when there's a stop transaction due to power loss, fixed edge cases where connectivity is lost, new ocpp key MaxEVCurrentOffered implemented which limits charge with key instead of smart charging handler, safety mechanisms for ocpp to be more robust
- AméliorationIn 4g, increased rssi range for "excellent" so that it indicates correctly when the reception is good
- AméliorationImproved data consumption
- AméliorationImproved robustness of update
- Mis à jourAccess point time increased to 15 minutes
- CorrectionHandled issues when SSID has whitespace
-
- CorrectionAccess point improvements.
- CorrectionFixed QA issues.
-
- NouveauNew direct method to obtain additional information for Smart Charging.
- NouveauFixed random reboot time.
- AméliorationFixed unset RFID.
- AméliorationFixed Unknown measurer and made distinction between Unknown measurer and wrongly configured measurer.
- AméliorationOCPP Free mode can be toggled through OCPP keys.
- Mis à jourFixed BLE connection with iphone and fixed bluetooth communication error that appeared on app.
- Mis à jourNetwork improvements. No interface resets performed at boot which improves bootup time. Network changes now don't require reboot. When changing WIFI settings or ip ethernet settings, it connects after setting it instead of rebooting.
- CorrectionFixed issue where things on screen were missing in one connector chargers.
- CorrectionFixed time/timezone issue caused when the date is off by a few days.
- CorrectionNew property added to toggle if vehicle should be able to charge even though measurers aren't working ( Only works when OCPP, payments or dynamic control isn't enabled ).
-
- NouveauReflect on screen when charge is paused.
- NouveauMade reboot time random.
- CorrectionIncreased SAS token time to live of azure.
-
- NouveauChanges made to reduce network usage that can be toggled on or off.
- NouveauFixed case where config is corrupted or missing and would give trouble at startup.
- NouveauWe now send dead letter if cpu gets too hot and cpu temperature is now logged.
- AméliorationFixed OCPP inverted measurer error.
- AméliorationAdded mechanism to disable or enable Wifi and bluetooth.
- AméliorationWe now report information regarding which type of connection to the internet the e-charger has.
- Mis à jourChanged led colors. Switched State A (now white) and State B (now green) colors.
- CorrectionFixed set threshold values and neopixel leds of Stm32. We can now also obtain control pilot value from Stm32.
- CorrectionOCPP ConnectionTimeOut value can now be changed on the fly.
- CorrectionWe now report iccid of sim card is connected. If sim is connected but we can't obtain iccid, we send dead letter.
- CorrectionFixed log download of http interface.
-
- NouveauLTE signal is now reflected correctly instead of always showing great signal.
- AméliorationFixed wathdog reboot after doing hard reset.
-
- NouveauAdded dynamic photovoltaic.
- NouveauAdded dead letters: measurer fails and kernel error.
- NouveauProperty "wifi_info" is now reported.
- NouveauProperty "wifi_static" can be set through ble.
- NouveauWe can now obtain statistics through direct method.
- NouveauAdded individual log level for each type of logger.
- NouveauAdded neopixel led type for stm32.
- NouveauWe can now set threshold values with stm32 and get control pilot value if debug log of "Stm32" is activated.
- AméliorationImprovements in dynamic control, fabrication, QA, Azure, OCPP, config handling, 4g, access point and stm32.
- AméliorationWe now obtain timezone through url.
- AméliorationRemoved raspbian logo and desktop during boot and added V2C logo.
- AméliorationChanged default language after fabrication from english to spanish.
- Mis à jourGeneral bug fixes.
- CorrectionWhen downgrading we ensure that version we downgrade to is compatible.
-
- NouveauFixed property "ocpp" change bug.
- AméliorationProperties "powerweekday", "powerweekend" and "phase_map" can be changed through bluetooth.
- AméliorationChanged configuration handling to differentiate internally and externally set variables so that externally set or obtained variables are handled accordingly following the property schemas.
- CorrectionWe now report wifi_static with static ip configuration.
- CorrectionStatistics are now saved locally.
-
- AméliorationMeasurer fails are now registered with modbusrtumeasurer.
- AméliorationScreen font bigger for small title.
- CorrectionValidate configuration with schemas during loading.
-
- NouveauOCPP authorize can now function by connector.
- NouveauOCPP WSS connection.
- NouveauFixed OCPP parent id tag bug.
- NouveauOCPP meter values now work for 3 phases.
- AméliorationFixed error 3 not appearing on screen.
- AméliorationFixed energy by hour bug.
- AméliorationChanged measurer reading approach for faster reads.
- AméliorationWith dynamic balancing we now show used and available power in frontend.
-
- AméliorationWe show dynamic balancing information on screen.
- AméliorationSimplified handling of configuration.
- AméliorationImproved dynamic balancing.
-
- AméliorationCharger won't reboot if car is in state B and OCPP or Payments is active.
- AméliorationWhen car changes from state C to B, charge information will persist on screen.
- AméliorationCurrent state charge now reports errors.
- AméliorationAdded configuration property validation.
- CorrectionDirect method to obtain dynamic balancing information.
- CorrectionGeneral dynamic balancing improvements.
- CorrectionOCPP improvements.
-
- CorrectionChanged remaining set_basic_unreported_config to set_basic_config.
-
- NouveauFix dynamic control bug, powerbytram is not being updated.
- NouveauFixed bug where whitelist of reported items wasn't being applied and properties weren't being stored in database.
- AméliorationRemoved non-repetitive logger.
- AméliorationChanged access point interface to change apn, with manual mode or mobile operator mode.
- Mis à jourRefactored config charge box. Removed BASIC_UNREPORTED and created whitelist of properties to report.
- Mis à jourPhase map is now not applied to installation meters.
- CorrectionFixed payment bug where a charge couldn't be started properly if charge was started with the hose unlocked.
- CorrectionFix bug with power being zero, dynamic control failing when there are no connectors.
- 3.1.8Mis à jourForce WIFI and bluetooth GPIO pins for compute module 4 to work.
- 3.1.7Mis à jourForce 4g GPIO pins for compute module 4 to work.
-
- AméliorationWhen we detect that measurers aren't working, we send an unblock command in case there's a charge and the charger has lost power.
- AméliorationCreate section BASIC_UNREPORTED for properties that are used but we don't want to report.
- AméliorationLocked value has persistance when measurers fail.
- CorrectionWhen we don't receive petitions from chromium we now press enter and Ctrl+F5 if there's anything we need to accept.
-
- CorrectionChanging WIFI configuration with bluetooth now reboots the charge point.
-
- AméliorationFixed configuration file so that software works with compute module 3 and 4.
- AméliorationChanged reboot logic. It will now reboot if there's a car connected but charge is not allowed.
- CorrectionChanged payments qr code.
- CorrectionWe can change log level with property.
-
- CorrectionMeter values fixed. We now send wh instead of kwh.
-
- NouveauPause is now reset when it goes back to state A.
- NouveauShow measurer error as "Error 3" on connector. Behaviour is that connector is locked until it's fixed.
- NouveauSet wire connected again.
- AméliorationFixed general network errors. Improved access point and wifi connectivity.
- CorrectionFixed error where timezone wasn't set correctly so time appeared incorrectly.
- CorrectionFixed payment_max_mode timeout bug.
-
- NouveauFixed power, it was shown in W and is now in Kw.
- AméliorationChange timezone automatically.
- CorrectionAdded triphasic phoenix contact measurer.
- SuppriméFixed removal of grey notification update.
-
- NouveauWhenever there's an action that provokes rebooting, it will show on screen that it's going to reboot and the cause.
- NouveauScreen orientation can now be set and depending on parameter.
- NouveauAdded error message 1 and 2.
- NouveauBluetooth patch so that bluetooth initialization takes less time.
- NouveauCreated patch system. System level changes will be applied with this system.
- AméliorationMeasurer refactoring.
- AméliorationImei obtention improved.
- AméliorationInitial version of bluetooth finished: Obtain properties change basic properties, program charge, reboot, add rfid and change wifi.
- AméliorationBoot improvements. "Page not found" isn't shown anymore. Boot is faster. There's a gif indicating that system is starting.
- AméliorationObsolete properties are now deleted automatically so that they aren't reported.
- Mis à jourRFID can now function with payments. If RFID is enabled with payments, registered cards will be able to start charges. If RFID is disabled with payments, no card will be able to start a charge.
- CorrectionLimited number of messages we can send to iothub.
- CorrectionIn OCPP, fixed sending of meter values. Now sending in wh and not in kwh.
- CorrectionBoot patch so that GPIO pin initialization takes less time.
- CorrectionMonophasic measurer Eastron SDM220 implemented.
- CorrectionImproved robustness on all direct methods.
- CorrectionFixed bug where it didn't reconnect properly to iothub when it disconnected.
- CorrectionCreated direct method to put a QR code on the OCPP screen.
- SuppriméRemoved wire_connected event telemetry.
- 3.0.9CorrectionFixed ocpp meter value Energy.Active.Import, when measurer is flipped.
-
- Mis à jourFixed error where e-Charger couldn't obtain dns when connected with WIFI.
- CorrectionFixed local load balancing when one connector was charging. Now when one connector is charging, it will charge at the set intensity.
- 3.0.7CorrectionFixed ocpp Remote Start Transaction and Remote Stop Transaction.
- 3.0.6CorrectionFixed error that ocurred in ocpp where it didn't clear properly the idtag when finishing a transaction.
-
- Mis à jourChanged access point ip from 192.168.44.1 to 192.168.4.1
- Mis à jourWe now report the charger's state instead of the requested vehicle state.
- Mis à jourChanged access point master password.
- CorrectionFixed websocket connection issue with nuitka compilation.
-
- AméliorationImproved update logs.
- 3.0.3NouveauMoved Version from center to right side and added V. before the version number.
- 3.0.2AméliorationSTM will now detect SPI bus communication errors and will automatically reset.
-
- NouveauScreen now shows when RFID card is registered.
- NouveauTop bar now shows version and if access point is accessible.
- NouveauAccess point interface now has, local load balancing, rfid card registering and log download.
- NouveauCheck that compute module and board have been created properly.
- AméliorationScreen is now monitored so that it refreshes in the case that no requests have been made after 15 seconds.
- AméliorationQA diagnostic is obtained through access point.
- AméliorationReduced access point available time to 10 minutes.
- CorrectionFixed bug where connector stopped working properly when sending intensity 0.
-
- NouveauInitial Version
6 sur 46