Updates für Pole Pro
Wir arbeiten kontinuierlich daran, die Funktionen von Pole Pro zu verbessern. Hier finden sich die neueste Version unserer Ladesäule und die zuletzt veröffentlichten Updates.
Neueste Version
6.1.3
Pole Pro
Sie haben den früheren Pole? Hier finden Sie seine Updates.
6.1.3Neueste Version
- BehobenThe charger no longer hangs when rebooting while shutting down the 4G module or dynamic power control
Frühere Versionen 46
- 6.1.2BehobenOCPP security event notifications are no longer sent when the connection uses no security profile (profile 0), since some central systems do not support them
-
- BehobenCorrected default APN for Wireless Logic SIM cards in Belgium
-
- NeuAudible buzzer feedback
- NeuSupport for registering multiple RFID cards
- NeuReading of the installation meter over Modbus RS485 on DC chargers
- NeuDynamic power control for DC installations — master and slave units now share and honor the installation power limit
- NeuLive display of actual consumption versus offered current on the charger screen
- NeuOn-screen guidance walks the user through registering an RFID card
- NeuOCPP connection password can now be set from the Cloud and Bluetooth
- NeuOCPP now supports security profiles, encrypted TLS connections and Basic Authentication for the central system
- VerbessertLanguage codes standardized to the ISO 639-1 format
- VerbessertReduced volume of messages sent to the Cloud
- VerbessertTime synchronization with the CSMS no longer floods the system log
- VerbessertLog rotation no longer loses history when the disk is full
- VerbessertSafer firmware updates
- VerbessertMore reliable connectivity with automatic failover between Ethernet and 4G
- VerbessertCharges history now loads page by page instead of the whole history at once, for a faster tab
- BehobenMeasurer error message now reads clearly
- BehobenMore accurate meter-reading validation
- BehobenCharge metrics are preserved if a charge is interrupted unexpectedly
- BehobenScreen orientation set in configuration is now applied correctly
- BehobenFree-charge mode could not be disabled from the installer panel
- BehobenDynamic power limit was not applied at tariff/hour boundaries, briefly leaving an installation without a limit
- BehobenResolved random service restarts (crashes) caused by network device discovery
-
- VerbessertMore reliable RFID card reading with optimized antenna configuration from first use
- VerbessertImproved stability and responsiveness of the charger's web interface
-
- NeuOCPP - Immediate "Preparing" status when receiving a remote start command via OCPP
- NeuWiFi disabled by default on devices without WiFi configured
- VerbessertMore reliable RFID card reading with periodic reader reinitialization
- VerbessertBetter cable connection detection and RFID timeout handling
- VerbessertCDP - More stable network device discovery, preventing unnecessary register/unregister cycles
- VerbessertImproved stability when applying configuration changes to the charger
- VerbessertAutomatic migration of legacy pending OCPP messages after update
- VerbessertImproved network handling when switching between manual and automatic IP configuration
- BehobenPower factor value conversion for Carlo Gavazzi meters
- BehobenImprovements in power measurement accuracy in single-phase or two-phase installations
- BehobenOCPP - Smart Charging profiles with defined duration now applied correctly
- BehobenOCPP - Local authentication cache overflow that could prevent charging sessions from startIing
- BehobenOCPP - OCPP transactions stuck due to unreleased semaphores or null keys
-
- NeuEnhanced web server for accessing and editing charger properties
- NeuVisual improvements to the web server interface
- NeuPersistent price display on screen when the payment system is active
- NeuRefined error reporting to the cloud
- NeuPower loss detection
- NeuWi-Fi disable option from the installer panel
- NeuNew buzzer system implementation for white boards
- VerbessertEnhanced RFID calibration with on-screen indicator during the process
- VerbessertRFID reader no longer forcibly activates when OCPP or Payments are active; explicit configuration is respected
- VerbessertRefined cable connect/disconnect notification on each event when payments are active
- VerbessertOptimized RFID card readings
- VerbessertOCPP - Improvements to the offline transaction queue
- VerbessertInternal connection optimization and overall performance improvements
- BehobenOCPP - Improved measurement value reporting
- BehobenRefined out-of-range measurement error detection
-
- NeuSoftware-level leak detection enable/disable
- VerbessertAdjusted cooldown time between charges when a leak is detected
- VerbessertOCPP - Improvements to the offline transaction queue
-
- VerbessertWhen OCPP is active, we now show on screen when card passed is not registered in central system.
- BehobenAfter update OCPP image and QR is now recovered.
-
- BehobenFixed issue where it didn't allow a remote start if a car is connected but not in an active transaction.
- BehobenFixed issue in setup interface.
- BehobenFixed monophasic Carlo Gavazzi measurer.
- BehobenFixed OCPP issue where it wouldn't charge in connector 2 if connector 1 is charging.
-
- VerbessertImproved network features mainly 4G connection.
-
- VerbessertImproved OCPP charge handling.
- VerbessertEnhanced reliability in the smart charging logic.
- VerbessertImproved features when stopping a charge with invalid identifiers.
- VerbessertImproved QR configuration for OCPP.
- VerbessertImproved error handling when sensors or communication components fail.
- VerbessertBetter log management to prevent the device’s storage from filling up.
- VerbessertImproved USB connection features.
- VerbessertImproved RFID calibration and detection display.
- VerbessertImproved features related to Bluetooth.
- VerbessertImproved dynamic power control allowing charge at minimum intensity if master is not detected.
-
- NeuManual timezone setting is now available – The user will be able to configure the timezone even if automatic detection is disabled
- NeuCreated a contingency page in case app is not running
- NeuAdded Italian option for screen
- NeuAdded default payment QR to pay without app
- NeuAdded new OCPP personalization options - The user can now set 2 QR codes on the screen
- VerbessertImproved updater
- VerbessertImproved network connections
- VerbessertImproved OCPP meter values
- VerbessertImproved discovering devices when dynamic control is active
- VerbessertImproved user interface when updates are in progress
- VerbessertLocal load balancing is now implemented as dynamic control based specific conditions
- VerbessertImproved Bluetooth connection
- VerbessertImproved 4g connections robustness
- VerbessertImproved STM32 lock timings
- VerbessertImproved OCPP now allows external intensity limits
- VerbessertImproved data consumption
- BehobenWhen locking a connector while charging, it now sends end charge telemetry correctly
- BehobenFixed dynamic control issues
- BehobenFixed Carlo Gavazzi power meter
- BehobenFixed OCPP LMS, diagnostics, and charging profile clearing
-
- NeuAdded shared library
- NeuTimezone can be set manually
- NeuTime is now synced with Central System if OCPP is active
- VerbessertImproved version/update manager
- VerbessertImproved megabyte conversion of Network Monitor
- VerbessertObtaining timezone now doesn't need to have correct time by using only http urls
- VerbessertMobile usb device name is now obtained dynamically since more usb ports might be used due to TPV
- BehobenFixed power control issues
- BehobenFixed that when locking connector during a charge it now ends correctly
- BehobenRecalculate reboot time when changing time with ble
- BehobenWe now show on screen when non registered RFID is passed while OCPP is active
- BehobenFixed OCPP freemode rfid issues
- BehobenDuplicate StatusNotifications are removed from offline queue
- BehobenFixed "infinite" OCPP offline queue issue
-
- NeuAPN can now be set manually
- VerbessertWe now show on screen different wifi images depending on how strong signal is to let know the user how good the connection is
- VerbessertGeneral OCPP improvements: we check connection to CS instead of internet for local functioning, we notify a real value now when there's a stop transaction due to power loss, fixed edge cases where connectivity is lost, new ocpp key MaxEVCurrentOffered implemented which limits charge with key instead of smart charging handler, safety mechanisms for ocpp to be more robust
- VerbessertIn 4g, increased rssi range for "excellent" so that it indicates correctly when the reception is good
- VerbessertImproved data consumption
- VerbessertImproved robustness of update
- AktualisiertAccess point time increased to 15 minutes
- BehobenHandled issues when SSID has whitespace
-
- BehobenAccess point improvements.
- BehobenFixed QA issues.
-
- NeuNew direct method to obtain additional information for Smart Charging.
- NeuFixed random reboot time.
- VerbessertFixed unset RFID.
- VerbessertFixed Unknown measurer and made distinction between Unknown measurer and wrongly configured measurer.
- VerbessertOCPP Free mode can be toggled through OCPP keys.
- AktualisiertFixed BLE connection with iphone and fixed bluetooth communication error that appeared on app.
- AktualisiertNetwork improvements. No interface resets performed at boot which improves bootup time. Network changes now don't require reboot. When changing WIFI settings or ip ethernet settings, it connects after setting it instead of rebooting.
- BehobenFixed issue where things on screen were missing in one connector chargers.
- BehobenFixed time/timezone issue caused when the date is off by a few days.
- BehobenNew property added to toggle if vehicle should be able to charge even though measurers aren't working ( Only works when OCPP, payments or dynamic control isn't enabled ).
-
- NeuReflect on screen when charge is paused.
- NeuMade reboot time random.
- BehobenIncreased SAS token time to live of azure.
-
- NeuChanges made to reduce network usage that can be toggled on or off.
- NeuFixed case where config is corrupted or missing and would give trouble at startup.
- NeuWe now send dead letter if cpu gets too hot and cpu temperature is now logged.
- VerbessertFixed OCPP inverted measurer error.
- VerbessertAdded mechanism to disable or enable Wifi and bluetooth.
- VerbessertWe now report information regarding which type of connection to the internet the e-charger has.
- AktualisiertChanged led colors. Switched State A (now white) and State B (now green) colors.
- BehobenFixed set threshold values and neopixel leds of Stm32. We can now also obtain control pilot value from Stm32.
- BehobenOCPP ConnectionTimeOut value can now be changed on the fly.
- BehobenWe now report iccid of sim card is connected. If sim is connected but we can't obtain iccid, we send dead letter.
- BehobenFixed log download of http interface.
-
- NeuLTE signal is now reflected correctly instead of always showing great signal.
- VerbessertFixed wathdog reboot after doing hard reset.
-
- NeuAdded dynamic photovoltaic.
- NeuAdded dead letters: measurer fails and kernel error.
- NeuProperty "wifi_info" is now reported.
- NeuProperty "wifi_static" can be set through ble.
- NeuWe can now obtain statistics through direct method.
- NeuAdded individual log level for each type of logger.
- NeuAdded neopixel led type for stm32.
- NeuWe can now set threshold values with stm32 and get control pilot value if debug log of "Stm32" is activated.
- VerbessertImprovements in dynamic control, fabrication, QA, Azure, OCPP, config handling, 4g, access point and stm32.
- VerbessertWe now obtain timezone through url.
- VerbessertRemoved raspbian logo and desktop during boot and added V2C logo.
- VerbessertChanged default language after fabrication from english to spanish.
- AktualisiertGeneral bug fixes.
- BehobenWhen downgrading we ensure that version we downgrade to is compatible.
-
- NeuFixed property "ocpp" change bug.
- VerbessertProperties "powerweekday", "powerweekend" and "phase_map" can be changed through bluetooth.
- VerbessertChanged configuration handling to differentiate internally and externally set variables so that externally set or obtained variables are handled accordingly following the property schemas.
- BehobenWe now report wifi_static with static ip configuration.
- BehobenStatistics are now saved locally.
-
- VerbessertMeasurer fails are now registered with modbusrtumeasurer.
- VerbessertScreen font bigger for small title.
- BehobenValidate configuration with schemas during loading.
-
- NeuOCPP authorize can now function by connector.
- NeuOCPP WSS connection.
- NeuFixed OCPP parent id tag bug.
- NeuOCPP meter values now work for 3 phases.
- VerbessertFixed error 3 not appearing on screen.
- VerbessertFixed energy by hour bug.
- VerbessertChanged measurer reading approach for faster reads.
- VerbessertWith dynamic balancing we now show used and available power in frontend.
-
- VerbessertWe show dynamic balancing information on screen.
- VerbessertSimplified handling of configuration.
- VerbessertImproved dynamic balancing.
-
- VerbessertCharger won't reboot if car is in state B and OCPP or Payments is active.
- VerbessertWhen car changes from state C to B, charge information will persist on screen.
- VerbessertCurrent state charge now reports errors.
- VerbessertAdded configuration property validation.
- BehobenDirect method to obtain dynamic balancing information.
- BehobenGeneral dynamic balancing improvements.
- BehobenOCPP improvements.
-
- BehobenChanged remaining set_basic_unreported_config to set_basic_config.
-
- NeuFix dynamic control bug, powerbytram is not being updated.
- NeuFixed bug where whitelist of reported items wasn't being applied and properties weren't being stored in database.
- VerbessertRemoved non-repetitive logger.
- VerbessertChanged access point interface to change apn, with manual mode or mobile operator mode.
- AktualisiertRefactored config charge box. Removed BASIC_UNREPORTED and created whitelist of properties to report.
- AktualisiertPhase map is now not applied to installation meters.
- BehobenFixed payment bug where a charge couldn't be started properly if charge was started with the hose unlocked.
- BehobenFix bug with power being zero, dynamic control failing when there are no connectors.
- 3.1.8AktualisiertForce WIFI and bluetooth GPIO pins for compute module 4 to work.
- 3.1.7AktualisiertForce 4g GPIO pins for compute module 4 to work.
-
- VerbessertWhen we detect that measurers aren't working, we send an unblock command in case there's a charge and the charger has lost power.
- VerbessertCreate section BASIC_UNREPORTED for properties that are used but we don't want to report.
- VerbessertLocked value has persistance when measurers fail.
- BehobenWhen we don't receive petitions from chromium we now press enter and Ctrl+F5 if there's anything we need to accept.
-
- BehobenChanging WIFI configuration with bluetooth now reboots the charge point.
-
- VerbessertFixed configuration file so that software works with compute module 3 and 4.
- VerbessertChanged reboot logic. It will now reboot if there's a car connected but charge is not allowed.
- BehobenChanged payments qr code.
- BehobenWe can change log level with property.
-
- BehobenMeter values fixed. We now send wh instead of kwh.
-
- NeuPause is now reset when it goes back to state A.
- NeuShow measurer error as "Error 3" on connector. Behaviour is that connector is locked until it's fixed.
- NeuSet wire connected again.
- VerbessertFixed general network errors. Improved access point and wifi connectivity.
- BehobenFixed error where timezone wasn't set correctly so time appeared incorrectly.
- BehobenFixed payment_max_mode timeout bug.
-
- NeuFixed power, it was shown in W and is now in Kw.
- VerbessertChange timezone automatically.
- BehobenAdded triphasic phoenix contact measurer.
- EntferntFixed removal of grey notification update.
-
- NeuWhenever there's an action that provokes rebooting, it will show on screen that it's going to reboot and the cause.
- NeuScreen orientation can now be set and depending on parameter.
- NeuAdded error message 1 and 2.
- NeuBluetooth patch so that bluetooth initialization takes less time.
- NeuCreated patch system. System level changes will be applied with this system.
- VerbessertMeasurer refactoring.
- VerbessertImei obtention improved.
- VerbessertInitial version of bluetooth finished: Obtain properties change basic properties, program charge, reboot, add rfid and change wifi.
- VerbessertBoot improvements. "Page not found" isn't shown anymore. Boot is faster. There's a gif indicating that system is starting.
- VerbessertObsolete properties are now deleted automatically so that they aren't reported.
- AktualisiertRFID can now function with payments. If RFID is enabled with payments, registered cards will be able to start charges. If RFID is disabled with payments, no card will be able to start a charge.
- BehobenLimited number of messages we can send to iothub.
- BehobenIn OCPP, fixed sending of meter values. Now sending in wh and not in kwh.
- BehobenBoot patch so that GPIO pin initialization takes less time.
- BehobenMonophasic measurer Eastron SDM220 implemented.
- BehobenImproved robustness on all direct methods.
- BehobenFixed bug where it didn't reconnect properly to iothub when it disconnected.
- BehobenCreated direct method to put a QR code on the OCPP screen.
- EntferntRemoved wire_connected event telemetry.
- 3.0.9BehobenFixed ocpp meter value Energy.Active.Import, when measurer is flipped.
-
- AktualisiertFixed error where e-Charger couldn't obtain dns when connected with WIFI.
- BehobenFixed local load balancing when one connector was charging. Now when one connector is charging, it will charge at the set intensity.
- 3.0.7BehobenFixed ocpp Remote Start Transaction and Remote Stop Transaction.
- 3.0.6BehobenFixed error that ocurred in ocpp where it didn't clear properly the idtag when finishing a transaction.
-
- AktualisiertChanged access point ip from 192.168.44.1 to 192.168.4.1
- AktualisiertWe now report the charger's state instead of the requested vehicle state.
- AktualisiertChanged access point master password.
- BehobenFixed websocket connection issue with nuitka compilation.
-
- VerbessertImproved update logs.
- 3.0.3NeuMoved Version from center to right side and added V. before the version number.
- 3.0.2VerbessertSTM will now detect SPI bus communication errors and will automatically reset.
-
- NeuScreen now shows when RFID card is registered.
- NeuTop bar now shows version and if access point is accessible.
- NeuAccess point interface now has, local load balancing, rfid card registering and log download.
- NeuCheck that compute module and board have been created properly.
- VerbessertScreen is now monitored so that it refreshes in the case that no requests have been made after 15 seconds.
- VerbessertQA diagnostic is obtained through access point.
- VerbessertReduced access point available time to 10 minutes.
- BehobenFixed bug where connector stopped working properly when sending intensity 0.
-
- NeuInitial Version
6 von 46