fbpx Menú flotante
V2C » Support Area » Trydan Support » Trydan user manual

User manual for Trydan

The V2C team thanks you for choosing Trydan, an e-Charger equipped with the latest technology to offer you the smartest charging experience. Refer to this user manual to fully enjoy all the potential of Trydan.

Make every charge a unique experience with V2C Cloud

Schedule, customize, and adjust each of your charges to achieve optimal experience and the best energy efficiency.

Available in both desktop and mobile versions, V2C Cloud ensures you have full control wherever you are.

Discover V2C Cloud
Table of contents
  1. Make every charge a unique experience with V2C Cloud
  2. General features
  3. Hose placement and removal
  4. Navigation menu interface
  5. Product number composition
  6. Safety warnings
  7. Do you need technical support?

This manual is subject to change without notice. The images shown below are representative and may differ from actual products.

General features

e-Charger

Trydan

Color

⚫ Black

Material

Polycarbonate MVR

Hose length

5m / 10m

Weight

7 kg

Hose type

Smooth / Coil

Operating
temperature

-25ºC a 50º

Storage
temperature

-40ºC a 70º

Display

Yes

Illumination according to charge status

Hose placement and removal

Hose placement

  1. Insert the hose into the support, leaving a small space at the bottom so that it does not hit the integrated locking clip.
  2. Slide the hose down to secure it in the integrated locking clip.

Hose removal

  1. Slide the hose up to release it from the locking clip.
  2. Pull the hose out of the support.

Navigation menu interface

Trydan has two buttons on the upper left side, as shown in the image. These buttons allow you to configure various parameters, providing an alternative to using the V2C Cloud platform.

To access the configuration, press both buttons simultaneously for 4 to 5 seconds.
The upper button is assigned to advance (+) and the lower button to retreat (-).
There are 3 main configuration categories: System, Additional, and Installation.

Switch between categories > Any button with a short press
Enter a specific category > Long press on the upper button
Switch between parameters within the category > Short presses
Access and modify a parameter > Long press on the upper button
Modify the parameter > Short presses
Save the configuration > Long press on either button

Button and display navigation manual

Product number composition

TRY32-1-L5-P-S

ModelTRY
Current32
Network typeSingle-phase1
Three-phase3
Hose typeSmooth 5mL5
Smooth 10 mL10
CoilM
SocketS
ProtectionsP
SchukoSC
AccessoriesLeakage detectorV2C – F
Remote controlV2C – R
Cable reel supportV2C – SOP
Stainless steel pedestalV2C – PED

Dynamic power control

Configure and customize the dynamic power control to optimize energy and prevent overloads.

‘Hey Alexa, start charging my electric car’

Turn the e-Charger on and off, adjust the intensity, and perform other functions with your voice.

LED Lighting

Learn the meaning of the different LED lighting colors of the logo.

Safety warnings

The owner must comply with safety instructions. V2C disclaims all responsibility for rights derived from non-compliance.
This mode 3 charging point is classified according to section 5 of UNE-EN 61851-1 in an EV supply system connected to an AC supply network. Depending on the chosen version, the EV supply system will be plug-and-cable or permanently connected. It can be used both outdoors and indoors and is suitable for restricted and non-restricted access.
Never use damaged, worn, or dirty charging connectors.
The owner must ensure the charger is always operated in perfect condition.
Regularly check that the plug or charging connector (including the charging cable) and the electric charging station housing are not damaged (visual inspection).
In case of defect, the electric charging station must be disconnected and replaced.
Repairing the charging station is prohibited; only the manufacturer can perform this task (the e-Charger must be replaced).
Do not make any unauthorized transformations or modifications to the charging station.
Adapters or converters/extenders are not allowed.
Do not remove any identification, such as safety symbols, warning signs, rating plates, identification plates, or line signage.
Ventilation: Forced ventilation is not required due to the manufacturing technology.
Unplug the charging cable by pulling the connector, not the cable. Danger of damage!
Never clean the electric charging station with a pressure washer (hose, high-pressure cleaner, etc.)!

Electrical Hazard! Installation, initial startup, and maintenance of the electric charging station must be carried out exclusively by competent and qualified technical personnel, fully responsible for compliance with installation provisions and existing standards.

V2C carries the CE mark. V2C applies the corresponding declarations of
conformity.

V2C complies with the ROHS directive (2011/65/EC). V2C applies the corresponding declarations of conformity.

Electrical and electronic equipment, as well as their accessories, must be disposed of separately from household waste.

If you have any suggestions to improve our services, please let us know by sending an email to [email protected].

Do you need technical support?

Generate a request in the Technical Support Centre and we will contact you as soon as possible to offer you the best solution.

Contact Technical Support